Üdv,
Van 1 haldokló Seagate winyóm, a bolti garanciája már lejárt, gyári még van rajta december 4-ig. Van valakinek tapasztalata, hogy kivel, és hová érdemes/olcsó visszaküldeni?
Sziasztok!
Adott két terrás lemez soft raid1ben megannyi doksival.
Ha formázva lett majd új ext partíció lett létrehozva mindkét lemezen, hozható róla vissza adat? Struktúrával együtt? Az adatok minél nagyobb százalékban történő visszanyerése lenne a cél.
Üdv,
Nem találtam kábeles alfórumot, szóval itt kérek segítséget.
Szükségem lenne kb. 4-4.5m hosszú külső SCSI kábelre, méghozzá fémházasra.
Mindkét végén 68 pólusú "fiú" csatlakozóval.
Hol tudok ilyet beszerezni?
Ha nem lehet, akkor megoldható a gyártása is. Ezesetben szükség lenne valamiféle leírásra, hogy hogyan kell csinálni, milyen segédanyagok kellenek hozzá stb.
Előre is köszönöm, ha valaki tud segíteni!
Hali,
Van egy SGI IS4000 3 talcas lemeztombom, sata vinyokkal es a sajat szoftverevel.
Van aki ismeri ezt a cuccot? Kis segitsegre lenne szuksegem mert se idom se energiam az elejetol vegig kinlodni a beuzemelest.
Lemezek benne vannak, csinaltam par raid5 tombot rajta. a kiajanlassal van bajom, hogy mukodik ennel a cuccnal a kiajanlas?
FC-n menne a dolog valszeg. Ez az FC-s kiajanlas nem tiszta nekem sajnos. Ha valaki tudna ebbe segiteni azt nagyon megkoszonnem.
Hanzo
Van pár hdd-m (mondjuk 4-5) amik még használhatóak, de eladni nem akarom. Egy gépre akarnám rákötni ezeket, valami külső torony formájában(nem fér már a gépben). A gépen van egy esata, egy pci slot(ide lehetne venni valami kártyát...), és 2 usb. Belső szabad sata nincs. Cél, hogy a 4-5 disk mind látszódjon a gépen.
Te hogy oldanád meg hardveresen?
Sziasztok
Egy médialejátszó mögé elsősorban videók (1-2% zene és fotó) tárolására szolgáló raid5 (mdraid) tömbbe melyik winyót választanátok az alábbiak közül:
WD Red
Seagate NAS
Seagate Video
Seagate Surveillance
Első gondolat a Seagate Video lenne, ha csak 1 lemezről lenne szó, valószínűleg nem is gondolkodnék rajta. De fene tudja, hogy raid-ben hogyan viselkedik, illetve a 2.5"-os mérete miatt is aggódom (rosszabb hőelvezetés)
A Surveillance esetében nem gond a RAID, de azt meg inkább erős és folyamatos írásra tervezték. Ráadásul az árával is kiugrik a mezőnyből.
És ott van még Seagate NAS meg a WD Red meg kifejezetten NAS-ra szánt dolog...
hi,
02:00.0 RAID bus controller: LSI Logic / Symbios Logic MegaRAID SAS 2108 [Liberator] (rev 05)
Subsystem: LSI Logic / Symbios Logic MR9260-16i
Ebbol szeetnek csinalni HBA-t.
Lehetseges egyaltalan? Meg sosem vegeztem hasonlo ganyolast. Pl. nem talalom, milyennek kene magat mutatni a flash-eles utan, milyen fw-t toltsek le hozza?
10x
t
UPDATE: mult heten megkaptam a cserevinyot (mivel megingott a bizalmam a Purple-ben, egy Redet kertem helyette, remeljuk ezzel mar nem lesz gond)
vettem nemreg egy WD Purple-t (a Red-et vagy ezt ajanlottak egy masik forumon, vegul a Purple-t valasztottam...)
tisztaban vagyok vele hogy megfigyelorendszerekhez ajanljak elsosorban, nekem otthonra NAS-ba kell gyenge torrentforgalomra illetve Time Machine backuphoz (vagyis jellemzoen kb. folyamatos, kis sebessegu iras/olvasas). Egy Sharkoon kulso hazban uldogel.
Viszont erdekes hibakat talaltam a rakotott Raspberry logjaban.
Ezen nekibuzdulva raeresztettem egy badblocksot egy desktop gepre kotve (amugy ezzel kezdtem volna, de olyan baromi sokaig tart, hogy inkabb nekialltam atmasolni ra a tobbi kulso vinyorol a cuccost, gondolva hogy ha baj van ugyis kibukik - hat ugy nez ki bejott :D).
az elso kb. 80%-ig siman elmegy kb. egyenletes tempoval, onnantol viszont nagyon durvan belassul, jelenleg itt all, az 'elapsed' az 5-10 percenkent lep elore, a szazalekjelzes lenyegeben mozdulatlan:
$ sudo badblocks -svn /dev/sdi
Checking for bad blocks in non-destructive read-write mode
From block 0 to 2930266583
Checking for bad blocks (non-destructive read-write test)
Testing with random pattern: 83.19% done, 48:09:17 elapsed. (0/0/0 errors)
jelenleg: Testing with random pattern: 83.19% done, 48:29:45 elapsed. (0/0/0 errors)
Szoval, most rossz a vinyo, elkepzelheto hogy a rack-kel van baj, netan valami beallitas/kernel/stb okozza a gondot? (ezek a tippjeim, csokkeno valoszinuseggel :D)
hdparm:
$ sudo hdparm -I /dev/sdi
/dev/sdi:
ATA device, with non-removable media
Model Number: WDC WD30PURX-64P6ZY0
Serial Number: WD-WCC4NDA2NYJD
Firmware Revision: 80.00A80
Transport: Serial, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
Supported: 9 8 7 6 5
Likely used: 9
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 5860533168
Logical Sector size: 512 bytes
Physical Sector size: 4096 bytes
Logical Sector-0 offset: 0 bytes
device size with M = 1024*1024: 2861588 MBytes
device size with M = 1000*1000: 3000592 MBytes (3000 GB)
cache/buffer size = unknown
Nominal Media Rotation Rate: 5400
Capabilities:
LBA, IORDY(can be disabled)
Queue depth: 32
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 0
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* NOP cmd
* DOWNLOAD_MICROCODE
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
SET_MAX security extension
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
Media Card Pass-Through
* General Purpose Logging feature set
* 64-bit World wide name
* URG for READ_STREAM[_DMA]_EXT
* URG for WRITE_STREAM[_DMA]_EXT
* IDLE_IMMEDIATE with UNLOAD
* WRITE_UNCORRECTABLE_EXT command
* {READ,WRITE}_DMA_EXT_GPL commands
* Segmented DOWNLOAD_MICROCODE
* Gen1 signaling speed (1.5Gb/s)
* Gen2 signaling speed (3.0Gb/s)
* Gen3 signaling speed (6.0Gb/s)
* Native Command Queueing (NCQ)
* Host-initiated interface power management
* Phy event counters
* Idle-Unload when NCQ is active
* NCQ priority information
* READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
DMA Setup Auto-Activate optimization
Device-initiated interface power management
* Software settings preservation
* SMART Command Transport (SCT) feature set
* SCT Write Same (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
unknown 206[12] (vendor specific)
unknown 206[13] (vendor specific)
unknown 206[14] (vendor specific)
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
supported: enhanced erase
438min for SECURITY ERASE UNIT. 438min for ENHANCED SECURITY ERASE UNIT.
Logical Unit WWN Device Identifier: 50014ee25fcf21ff
NAA : 5
IEEE OUI : 0014ee
Unique ID : 25fcf21ff
Checksum: correct
a dmesg vege:
[839547.898949] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839547.915060] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839547.915062] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839547.915704] sd 26:0:0:0: [sdi] Unhandled error code
[839547.915707] sd 26:0:0:0: [sdi]
[839547.915709] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[839547.915710] sd 26:0:0:0: [sdi] CDB:
[839547.915711] Read(16): 88 00 00 00 00 01 22 95 1a 68 00 00 00 80 00 00
[839547.915719] end_request: I/O error, dev sdi, sector 4875164264
[839547.915722] quiet_error: 20 callbacks suppressed
[839547.915723] Buffer I/O error on device sdi, logical block 609395533
[839547.915728] Buffer I/O error on device sdi, logical block 609395534
[839547.915729] Buffer I/O error on device sdi, logical block 609395535
[839547.915731] Buffer I/O error on device sdi, logical block 609395536
[839547.915732] Buffer I/O error on device sdi, logical block 609395537
[839547.915734] Buffer I/O error on device sdi, logical block 609395538
[839547.915736] Buffer I/O error on device sdi, logical block 609395539
[839547.915737] Buffer I/O error on device sdi, logical block 609395540
[839547.915739] Buffer I/O error on device sdi, logical block 609395541
[839547.915740] Buffer I/O error on device sdi, logical block 609395542
[839585.802913] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839585.818810] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839585.818812] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839616.920001] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839616.935854] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839616.935856] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839647.908818] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839647.924918] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839647.924921] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839678.897791] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839678.913885] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839678.913887] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839709.890552] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839709.906652] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839709.906654] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839741.003493] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839741.019702] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839741.019705] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839741.020348] sd 26:0:0:0: [sdi] Unhandled error code
[839741.020350] sd 26:0:0:0: [sdi]
[839741.020352] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[839741.020353] sd 26:0:0:0: [sdi] CDB:
[839741.020355] Read(16): 88 00 00 00 00 01 22 95 1a 80 00 00 00 80 00 00
[839741.020362] end_request: I/O error, dev sdi, sector 4875164288
[839800.932808] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839800.948811] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839800.948814] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839831.985714] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839832.001765] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839832.001768] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839863.038450] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839863.054528] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839863.054531] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839894.027653] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839894.043425] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839894.043428] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839925.016411] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839925.032600] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839925.032602] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839956.005481] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839956.021436] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839956.021438] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[839956.022158] sd 26:0:0:0: [sdi] Unhandled error code
[839956.022159] sd 26:0:0:0: [sdi]
[839956.022160] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
[839956.022161] sd 26:0:0:0: [sdi] CDB:
[839956.022162] Read(16): 88 00 00 00 00 01 22 95 22 00 00 00 00 80 00 00
[839956.022176] end_request: I/O error, dev sdi, sector 4875166208
[839995.990121] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[839996.006184] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[839996.006186] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[840027.075191] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[840027.091243] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[840027.091246] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[840058.064081] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[840058.080084] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[840058.080087] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[840089.053124] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[840089.068979] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[840089.068981] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
[840120.041972] usb 4-4: reset SuperSpeed USB device number 2 using xhci_hcd
[840120.061915] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b591480
[840120.061917] xhci_hcd 0000:00:14.0: xHCI xhci_drop_endpoint called with disabled ep ffff88029b5914c0
es vegul smartctl:
$ sudo smartctl --all /dev/sdi
smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.0-34-generic] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD30PURX-64P6ZY0
Serial Number: WD-WCC4NDA2NYJD
LU WWN Device Id: 5 0014ee 25fcf21ff
Firmware Version: 80.00A80
User Capacity: 3.000.592.982.016 bytes [3,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Thu Oct 2 09:01:13 2014 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (41280) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 414) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 088 064 051 Pre-fail Always - 82502
3 Spin_Up_Time 0x0027 185 182 021 Pre-fail Always - 5733
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 85
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 517
10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 49
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 21
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 75
194 Temperature_Celsius 0x0022 112 108 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 000 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Ahoj!
Az a kiváló feladat talált meg, hogy minél gyorsabban minél több pendrive-ra másoljak fel kb 7 GB-nyi adatot (olyan 100 file). Jelenleg egy másolás kb fél óra.
A céleszközök nagyon drágák, így nem igazán opció. Kinek milyen ötlete van?
Köszönöm: Ny
Sziasztok,
Adott egy Intel 2 procis E5-2620 szerver, LSI SAS 9211-8i 6 GB/s 8 portos raid vezérlővel, Linux web szerver lesz, Ngynx+myqsl.
Szeretnék bele SSD rakni, sokat olvastam utána, és az Intel SSD mellett tettem le a voksot.
Az Intel SSD-k közül melyiket ajánlanátok, 5db-ot szeretnék raid 10-ben (1db hotspare), hogy gyors, stabil, és tartós rendszert kapjak.
Amire kell a hasznos méret 100 GB is elég, így nem a méret a lényeg.
320, 520, 530, 730, S3500, S3700
Raid 10-nél van valami spec beállítás Linuxon, amit be kell állítani az SSD miatt?
Ha valakinek van más SSD-vel tapasztalata raid10-ben (több éve üzemelő) azt is meghallgatnám.
szerk:
A kinézett széria az Intel 730-as sorozatából való, van benne Enhanced Power Loss Data Protection:
http://ark.intel.com/products/81038/Intel-SSD-730-Series-240GB-2_5in-SA…
A 730-as szériával valakinek van tapasztalata?
Köszönettel:
Joda