NeroLinux nem ismeri fel a DVD írót

Üdv!

A következő gondom támadt: k3b-vel tudok DVD-t írni, de a NeroLinux3 nem ismeri fel az ATAPI DVD írómat.
A gond ott van, hogy a SCSI emuláció nem a DVD írómat emulálja, hanem a SATA HDD-met.
dmesg idevágó része:

Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> GSI 20 (level, low) -> IRQ 19
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
    ide0: BM-DMA at 0x1410-0x1417, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0x1418-0x141f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
Marking TSC unstable due to: possible TSC halt in C2.
Time: acpi_pm clocksource has been installed.
Probing IDE interface ide1...
hdc: Optiarc DVD RW AD-7540A, ATAPI CD/DVD-ROM drive
Device driver ide1 lacks bus and class support for being resumed.
ide1 at 0x170-0x177,0x376 on irq 15
PCI driver VIA_IDE lacks driver specific resume support.
hdc: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
sata_via 0000:00:0f.0: version 2.2
ACPI: PCI Interrupt 0000:00:0f.0[B] -> GSI 20 (level, low) -> IRQ 19
sata_via 0000:00:0f.0: routed to hard irq line 10
scsi0 : sata_via
Device driver host0 lacks bus and class support for being resumed.
scsi1 : sata_via
Device driver host1 lacks bus and class support for being resumed.
ata1: SATA max UDMA/133 cmd 0x00011430 ctl 0x00011426 bmdma 0x00011400 irq 19
ata2: SATA max UDMA/133 cmd 0x00011428 ctl 0x00011422 bmdma 0x00011408 irq 19
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-7: FUJITSU MHV2040BH, 00000025, max UDMA/100
ata1.00: 78140160 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
ata2: SATA link down 1.5 Gbps (SStatus 0 SControl 300)
Device driver target0:0:0 lacks bus and class support for being resumed.
scsi 0:0:0:0: Direct-Access     ATA      FUJITSU MHV2040B 0000 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0

A kernel configom elérhető itt.