W8.1 Hdd csere után lemezképről visszaállítási hiba - MEGOLDVA !

Fiam Óbudai Egyetem tanuló + Goggle keresés + MS megoldás és 60 perc.
A lemezképről visszarakva az egész mentés kisebb HDD-re, parancssorból :
wbadmin start recovery -version:02/18/2015-12:55 -items:c: -itemType:volume
-backuptarget:d: -recoverytarget:e: -quiet

Shift + F10 -el lehet előhívni telepítőben a cmd-t ha meg helyreállító lemez van akkor meg van olyan opció hogy Command prompt

wbadmin syntaxisai
https://technet.microsoft.com/hu-hu/library/cc742070(v=ws.10).aspx

To recover the System manually using Volume recovery
 
By using this workaround, at minimum the OS critical partitions should be of the same size for the volume recovery.
 
To recovery the System manually from Windows Recovery Environment (when BMR – Complete PC Restore is not working), user has to recover all the partitions individually and then set the BCD boot entries.
 
Please follow the below mentioned steps:
 
1)    Get the backup version from the backup target.
2)    From version, get the size of partitions at the time of backup.
3)    Recreate the partitions manually with same or more size.
4)    Perform volume recovery of Individual volumes.
5)    Set the Active bit for System volume.
6)    Fix the Boot entries.
 
Please replace anything marked under <> with actual values. The yellow marked entries are for sample only. We have to pick the actual values from his system. Also assuming the Boot disk is disk 0 in this case.
 
Open Command prompt:
1)    Do wbadmin get versions –backuptarget:.
a.    Select the version id from. E.g. Version identifier: 02/11/2009-09:14
Note: If the backup target is network share, then run “start /w wpeinit” to enable networking.
 
2)    Do wbadmin get items –version: -backuptarget:
a.    This will give the list of volumes that were backed up and their sizes.
 
3)    Using Diskpart, recreate your volumes of the same or more size. Assume that the Boot disk is Disk 0 and is empty. Disk 0 is the boot disk and is the first disk in BIOS boot order.
If the required partitions are already present then skip the steps below.
a.    Diskpart.exe
b.    List disk
c.    Select disk 0.
d.    Create par primary  size=        
e.    Format fs=ntfs quick label=”OS”               (Format the OS partition with NTFS)
f.     Assign letter=D                 (assign drive letter D: to OS volume)
g.    Do the same for all the volumes you want to recover.
h.    Detail disk
i.      It lists the newly created partitions.
 
4)    To recover the volumes one by one,
a.    Do wbadmin get items –version: -backuptarget: .
b.    Select the volume id or drive letter for OS volume that was backed up. 
E.g. C: corresponds to the OS volume at backup time.
c.    Wbadmin start recovery –version: -backuptarget: -itemType:Volume –items:C:  -recoverytarget:D:
d.    Do the same for all the other volumes. Make sure that minimum space requirement is met.
e.    Set the active bit of System volume from Diskpart.
f.     Diskpart.exe ->
                                          i.    Select volume D:
                                         ii.    active
5)    Reboot the OS and boot back into WinRE as OS is not yet bootable.
6)    Select Startup-Repair option to fix the BCD boot entries.
7)    Reboot and OS should be in a bootable state.
8)    If OS is still not bootable, use bcdedit.exe/bootrec.exe in WinRE to fix the BCD boot options.