[Megoldva] Új gépet szeretnék tavaszig

Miert lenne vekony? Amit felsoroltal az nincs 500 euro, o pedig 5-600-at mondott.

Tápon nem spórolnék ennyire.

Szerintem azt semmiképp, inkább 3200G vagy 3400G processzort és megoldva a videokártya téma, ha akar bármikor vehet erősebbet a gépbe, de a 1030 annyira gyengus, hogy nincs értelme megvenni.

Nem tűnik rossznak, az 1650 GTX mellé viszont akkor nem kell G jelű processzor, azonos árú sima Ryzen pl. 2600x vagy 3600 jobb választás lehet.

Esetleg egy jobb minosegu tap, de amugy rendben van.

sima 1650 helyett vagy 1650 Super vagy 1660 Super kártyát nézzél és egy Ryzen 5 2600-as proci is elég lesz a cucchoz.

Mivel nagyon nem bővítette az előző gépét sem azért javasoltam az A320-as lapot. Olcsó és minden finomság rajta van.

bocs benéztem, az A520 chipsetes lapok csak a 3000-es vagy 5000-es ryzeneket támogatják csak, gondolom még drágák is, úgyhogy kilőve..... 

x-es végű 95w-os procihoz illik venni egy kisebb normálisabb hűtőt, mert a gyári kevés neki, hűtésteljesítményben még hagyján, de brutál hangos lesz ha leterheled (pl. aida64-CPU+FPU), és a hőmérséklet is 90 fok+ lesz.... a sima 65w-os 2600-al ilyen szempontból jobban jártál volna. Az az LC-Power táp a másik gyenge pont a rendszerben, de amúgy rendben van.

 Én hagytam neki megkeresni a szenzorokat így:

sensors-detect
# sensors-detect version 3.6.0
# System: Micro-Star International Co., Ltd. MS-7B89 [1.0]
# Board: Micro-Star International Co., Ltd. B450M MORTAR MAX (MS-7B89)
# Kernel: 5.10.1 x86_64
# Processor: AMD Ryzen 7 3700X 8-Core Processor (23/113/0)

This program will help you determine which kernel modules you need
to load to use lm_sensors most effectively. It is generally safe
and recommended to accept the default answers to all questions,
unless you know what you're doing.

Gentoo config file protection is active. Every file this program will
modify must be merged before the change will become active using
default Gentoo tools such as dispatch-conf, cfg-update, and etc-update.

Some south bridges, CPUs or memory controllers contain embedded sensors.
Do you want to scan for them? This is totally safe. (YES/no): y
Silicon Integrated Systems SIS5595...                       No
VIA VT82C686 Integrated Sensors...                          No
VIA VT8231 Integrated Sensors...                            No
AMD K8 thermal sensors...                                   No
AMD Family 10h thermal sensors...                           No
AMD Family 11h thermal sensors...                           No
AMD Family 12h and 14h thermal sensors...                   No
AMD Family 15h thermal sensors...                           No
AMD Family 16h thermal sensors...                           No
AMD Family 17h thermal sensors...                           Success!
    (driver `k10temp')
AMD Family 15h power sensors...                             No
AMD Family 16h power sensors...                             No
Hygon Family 18h thermal sensors...                         No
Intel digital thermal sensor...                             No
Intel AMB FB-DIMM thermal sensor...                         No
Intel 5500/5520/X58 thermal sensor...                       No
VIA C7 thermal sensor...                                    No
VIA Nano thermal sensor...                                  No

Some Super I/O chips contain embedded sensors. We have to write to
standard I/O ports to probe them. This is usually safe.
Do you want to scan for Super I/O sensors? (YES/no): y
Probing for Super-I/O at 0x2e/0x2f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               No
Trying family `ITE'...                                      No
Probing for Super-I/O at 0x4e/0x4f
Trying family `National Semiconductor/ITE'...               No
Trying family `SMSC'...                                     No
Trying family `VIA/Winbond/Nuvoton/Fintek'...               Yes
Found `Nuvoton NCT6797D Super IO Sensors'                   Success!
    (address 0xa20, driver `nct6775')

Some systems (mainly servers) implement IPMI, a set of common interfaces
through which system health data may be retrieved, amongst other things.
We first try to get the information from SMBIOS. If we don't find it
there, we have to read from arbitrary I/O ports to probe for such
interfaces. This is normally safe. Do you want to scan for IPMI
interfaces? (YES/no): y
Probing for `IPMI BMC KCS' at 0xca0...                      No
Probing for `IPMI BMC SMIC' at 0xca8...                     No

Some hardware monitoring chips are accessible through the ISA I/O ports.
We have to write to arbitrary I/O ports to probe them. This is usually
safe though. Yes, you do have ISA I/O ports even if you do not have any
ISA slots! Do you want to scan the ISA I/O ports? (yes/NO): 

Lastly, we can probe the I2C/SMBus adapters for connected hardware
monitoring devices. This is the most risky part, and while it works
reasonably well on most systems, it has been reported to cause trouble
on some systems.
Do you want to probe the I2C/SMBus adapters now? (YES/no): 
Using driver `i2c-piix4' for device 0000:00:14.0: AMD KERNCZ SMBus

Next adapter: ...

...
Now follows a summary of the probes I have just done.
Just press ENTER to continue: 

Driver `nct6775':
  * ISA bus, address 0xa20
    Chip `Nuvoton NCT6797D Super IO Sensors' (confidence: 9)

Driver `k10temp' (autoloaded):
  * Chip `AMD Family 17h thermal sensors' (confidence: 9)

Do you want to overwrite '/etc/modules-load.d/lm_sensors.conf'? (yes/NO): y

 * IMPORTANT: At least 1 config file(s) in '/etc' need updating.
 * See the CONFIGURATION FILES and CONFIGURATION FILES UPDATE TOOLS
 * sections of the emerge man page to learn how to update config files.

Note: You only have created the required configuration to autoload the
required modules to use your sensors on boot. If you want to start using
your sensors right now you have to either load them now once manually, to
reboot this system or to execute the following command(s) _AFTER_
you have updated your config files:

  # systemctl restart systemd-modules-load

saturn /mnt/Extern/Gbackup # dmidecode -t 2
# dmidecode 3.2
Getting SMBIOS data from sysfs.
SMBIOS 2.8 present.

Handle 0x0002, DMI type 2, 15 bytes
Base Board Information
	Manufacturer: Micro-Star International Co., Ltd.
	Product Name: B450M MORTAR MAX (MS-7B89)
	Version: 1.0
	Serial Number: JC16175121
	Asset Tag: To be filled by O.E.M.
	Features:
		Board is a hosting board
		Board is replaceable
	Location In Chassis: To be filled by O.E.M.
	Chassis Handle: 0x0003
	Type: Motherboard
	Contained Object Handles: 0

saturn /mnt/Extern/Gbackup # sensors
nouveau-pci-2700
Adapter: PCI adapter
GPU core:    1000.00 mV (min =  +0.90 V, max =  +1.00 V)
temp1:        +65.0°C  (high = +95.0°C, hyst =  +3.0°C)
                       (crit = +122.0°C, hyst =  +2.0°C)
                       (emerg = +125.0°C, hyst = +10.0°C)

k10temp-pci-00c3
Adapter: PCI adapter
Vcore:         1.55 V  
Vsoc:          1.24 V  
Tctl:         +56.6°C  
Tdie:         +56.6°C  
Tccd1:        +56.5°C  
Icore:         0.00 A  
Isoc:          7.13 A  

nvme-pci-0100
Adapter: PCI adapter
Composite:    +51.9°C  (low  =  -5.2°C, high = +83.8°C)
                       (crit = +87.8°C)

nouveau-pci-2800
Adapter: PCI adapter
GPU core:    1000.00 mV (min =  +0.90 V, max =  +1.00 V)
temp1:        +65.0°C  (high = +95.0°C, hyst =  +3.0°C)
                       (crit = +122.0°C, hyst =  +2.0°C)
                       (emerg = +125.0°C, hyst = +10.0°C)

nct6797-isa-0a20
Adapter: ISA adapter
in0:                     1.26 V  (min =  +0.00 V, max =  +1.74 V)
in1:                     1.01 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in2:                     3.41 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in3:                     3.36 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in4:                     1.01 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in5:                   152.00 mV (min =  +0.00 V, max =  +0.00 V)  ALARM
in6:                   624.00 mV (min =  +0.00 V, max =  +0.00 V)  ALARM
in7:                     3.39 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in8:                     3.36 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in9:                     1.82 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in10:                    0.00 V  (min =  +0.00 V, max =  +0.00 V)
in11:                  640.00 mV (min =  +0.00 V, max =  +0.00 V)  ALARM
in12:                    1.10 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in13:                  680.00 mV (min =  +0.00 V, max =  +0.00 V)  ALARM
in14:                    1.54 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
fan1:                     0 RPM  (min =    0 RPM)
fan2:                  2061 RPM  (min =    0 RPM)
fan3:                     0 RPM  (min =    0 RPM)
fan4:                     0 RPM  (min =    0 RPM)
fan5:                     0 RPM  (min =    0 RPM)
SYSTIN:                 +45.0°C  (high = +127.0°C, hyst = +105.0°C)  sensor = CPU diode
CPUTIN:                 +46.0°C  (high = +127.0°C, hyst = +105.0°C)  sensor = thermistor
AUXTIN0:                +48.0°C  (high = +127.0°C, hyst = +75.0°C)  sensor = thermistor
AUXTIN1:               -128.0°C    sensor = thermistor
AUXTIN2:                +47.0°C    sensor = thermistor
AUXTIN3:                 -3.0°C    sensor = thermistor
SMBUSMASTER 0:          +56.5°C  
PCH_CHIP_CPU_MAX_TEMP:   +0.0°C  
PCH_CHIP_TEMP:           +0.0°C  
PCH_CPU_TEMP:            +0.0°C  
intrusion0:            ALARM
intrusion1:            ALARM
beep_enable:           disabled

A végén a sensors-ra kiírta amit ki tudott olvasni. A Conky még várat magára, épp LiveUSB összeállításban vagyok még, desktop csak utána lesz. Ha addig van megoldásod, szívesen látnám és ha nem lesz addig itt semmi, akkor írom az enyém.