Kernel VFS hibaüzenet

Fórumok

Kernel VFS hibaüzenet

Hozzászólások

Sziasztok!

Kérnék egy kis segítséget.

Van egy új rendszerem sata vinyókkal és a 2.6.8-as kernel nem ismeri fel.Ez önmagában nem lenne baj bár úgy tudom már kellen ismernie (lehet rosszul).

Az ata-as vinyora installálás után majd sikeres kernel fordítása után induláskor a következő üzenet fogad:

VFS: Cannot open root device "341" or unknown-block 3.65
Please append a correct "root" boot option. :cry:
Pedig jól állítottam be a lilo-t!

Mi lehet a baj?

Sata HDD SCSI-ként látszik ebből ered a gubi ...

/dev/sdx

Szerintem az IDE vezérlők modulként vannak beforgatva. Javas
lom, hogy ne modulként, hanem fixen forgasd bele a kernelbe.

Üdv:

Mac

[quote:2835a153db="mackosajt"]Szerintem az IDE vezérlők modulként vannak beforgatva. Javas
lom, hogy ne modulként, hanem fixen forgasd bele a kernelbe.

Üdv:

Mac

Vagy rakhatod az initrd -be is.
Milyen alaplapod van?

intel 945 GTP lapom van.
A sata winyók még nincsenek használva, csak az ata-s winyót nem látja

intel 945 GTP lapom van.
A sata winyók még nincsenek használva, csak az ata-s winyót nem látja

Mit értesz az alatt hogy scsi-kén látszik?

A kernelben is ott van a scsi eszközök között!

Vagy rosszul mondom?

[quote:a89d079b75="uc"]intel 945 GTP lapom van.
A sata winyók még nincsenek használva, csak az ata-s winyót nem látja

A kernelbe belefordítottad az Intel IDE támogatást?

[quote:3a27411bca="uc"]Mit értesz az alatt hogy scsi-kén látszik?

A kernelben is ott van a scsi eszközök között!

Vagy rosszul mondom?

Na most kezd zavarodni a kép. Az pata vezérlőt nem látja vagy az sata vazérlőt? A SATA -s merevlemezek a 2.6.x kernelben SCSI eszközként vannak jelen. Így a kernelbe bele kell fordítani a SCSI támogatást és az SCSI drivereknél ki kell választani az Intel SATA vezérlőt is, azt is bele kell fordítani a kernelbe. A PATA -s merevlemezekhez IDE támogatás kell. Azt is be kell fordítani a kernelbe.

Laci

a sata vezérlőt a 2.6.8 nem látja.
A hibaüzenet pedig az ata-s diszken jelentkezik ha indítom az új kernelt

[quote:fe0fbaa8fd="uc"]a sata vezérlőt a 2.6.8 nem látja.
A hibaüzenet pedig az ata-s diszken jelentkezik ha indítom az új kernelt

A lilo konfigját beküldhetnéd ha tudod, mert lehet hogy ott van a kutyus elásva.
Egyébként ezt támogatja szerintetek a 2.6.8 kernel: Serial ATA 3.0 Gbps (mert ez van ezen az Intel alaplapon).

[quote:140318ae79="uc"]a sata vezérlőt a 2.6.8 nem látja.
A hibaüzenet pedig az ata-s diszken jelentkezik ha indítom az új kernelt

Meg azért én megpróbálnám a 2.6.14 -es kernelt.

pont most fordul úgy ahogy tanácsoltátok!

[quote:682a966a02="uc"]pont most fordul úgy ahogy tanácsoltátok!

Igen, a 2.6.14 kernel changelogjában találtam ezt:
This patch adds the Intel ICH7-M DH DID to the ahci.c file for AHCI mode SATA support.
Szerintem ezzel már jó lesz.

köszi hogy utánanéztél, mindjárt kiderül az eredmény. A lilo-t pedig megcsinálja a make install csak az elérési utat kell átírni.

még egy kérdés!

Hogy tudok ebből bootolható install cd-t csinálni ha esetleg sikerül a fordítás? Vagy milyen módon jut át a jó kernel a sata-s winyókra?

itt a lilo.conf

# /etc/lilo.conf - See: `lilo(8)' and `lilo.conf(5)',
# --------------- `install-mbr(8)', `/usr/share/doc/lilo/',
# and `/usr/share/doc/mbr/'.

# +---------------------------------------------------------------+
# | !! Reminder !! |
# | |
# | Don't forget to run `lilo' after you make changes to this |
# | conffile, `/boot/bootmess.txt' (if you have created it), or |
# | install a new kernel. The computer will most likely fail to |
# | boot if a kernel-image post-install script or you don't |
# | remember to run `lilo'. |
# | |
# +---------------------------------------------------------------+

# Specifies the boot device. This is where Lilo installs its boot
# block. It can be either a partition, or the raw device, in which
# case it installs in the MBR, and will overwrite the current MBR.
#
boot=/dev/hdb

# Specifies the device that should be mounted as root. (`/')
#
root=/dev/hdb1

# Enable map compaction:
# Tries to merge read requests for adjacent sectors into a single
# read request. This drastically reduces load time and keeps the
# map smaller. Using `compact' is especially recommended when
# booting from a floppy disk. It is disabled here by default
# because it doesn't always work.
#
# compact

# Installs the specified file as the new boot sector
# You have the choice between: text, bmp, and menu
# Look in lilo.conf(5) manpage for details
#
install=menu

# Specifies the location of the map file
#
map=/boot/map

# You can set a password here, and uncomment the `restricted' lines
# in the image definitions below to make it so that a password must
# be typed to boot anything but a default configuration. If a
# command line is given, other than one specified by an `append'
# statement in `lilo.conf', the password will be required, but a
# standard default boot will not require one.
#
# This will, for instance, prevent anyone with access to the
# console from booting with something like `Linux init=/bin/sh',
# and thus becoming `root' without proper authorization.
#
# Note that if you really need this type of security, you will
# likely also want to use `install-mbr' to reconfigure the MBR
# program, as well as set up your BIOS to disallow booting from
# removable disk or CD-ROM, then put a password on getting into the
# BIOS configuration as well. Please RTFM `install-mbr(8)'.
#
# password=tatercounter2000

# Specifies the number of deciseconds (0.1 seconds) LILO should
# wait before booting the first image.
#
delay=20

# You can put a customized boot message up if you like. If you use
# `prompt', and this computer may need to reboot unattended, you
# must specify a `timeout', or it will sit there forever waiting
# for a keypress. `single-key' goes with the `alias' lines in the
# `image' configurations below. eg: You can press `1' to boot
# `Linux', `2' to boot `LinuxOLD', if you uncomment the `alias'.
#
# message=/boot/bootmess.txt
prompt
# delay=100
# timeout=100

# Specifies the VGA text mode at boot time. (normal, extended, ask, <mode>)
#
# vga=ask
# vga=9
#
vga=normal

# Kernel command line options that apply to all installed images go
# here. See: The `boot-prompt-HOWTO' and `kernel-parameters.txt' in
# the Linux kernel `Documentation' directory.
#
# append=""

# If you used a serial console to install Debian, this option should be
# enabled by default.
# serial=

#
# Boot up Linux by default.
#
default=Linux

image=/vmlinuz
label=Linux
read-only
# restricted
# alias=1

initrd=/initrd.img

image=/vmlinuz.old
label=LinuxOLD
read-only
optional
# restricted
# alias=2

initrd=/initrd.img.old
image=/boot/vmlinuz
label=szilinux
read-only

# If you have another OS on this machine to boot, you can uncomment the
# following lines, changing the device name on the `other' line to
# where your other OS' partition is.
#
# other=/dev/hda4
# label=HURD
# restricted
# alias=3

A primary slave merevlemzre telepítetted a rendszert? A lilo ott keresné a rendszert. Mikor kernelt fordítasz, akkor Az IDE résznél az SATA -t ne válazd ki (mellé is van írva, hogy depreceted), mert az nem lesz kompatibilis. A cat /proc/partitions parancsnak mi a kimenete?

Azt hiszem rájöttem, bent hagytam a ramdisk opciót és az lehet hogy nem jó?

[quote:b2b20363fa="uc"]Azt hiszem rájöttem, bent hagytam a ramdisk opciót és az lehet hogy nem jó?

Jelen esetben ez nem igen zavarhat be szerintem.