Sikerült már valakinek a Nokia 3220 -as telefont kezelni linux alatt? (Fájlok fel - le töltése stb) CA-42 kábelem van hozzá, kernelbe bele van forgatva a CA-42 támogatás. Gnokii 0.6.14 van a gépemen. Mit kéne csinálnom, hogy működjön? (Xgnokii - vel próbáltam) Fedora Core 6-ot használok.
A dmesg fontos része:
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for ark3116
usbcore: registered new interface driver ark3116
drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101
usbcore: registered new interface driver cp2101
drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07
drivers/usb/serial/usb-serial.c: USB Serial support registered for DeLorme Earthmate USB
drivers/usb/serial/usb-serial.c: USB Serial support registered for HID->COM RS232 Adapter
drivers/usb/serial/usb-serial.c: USB Serial support registered for Nokia CA-42 V2 Adapter
usbcore: registered new interface driver cypress
drivers/usb/serial/cypress_m8.c: Cypress USB to Serial Driver v1.09
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
drivers/usb/serial/usb-serial.c: USB Serial support registered for TI USB 3410 1 port adapter
drivers/usb/serial/usb-serial.c: USB Serial support registered for TI USB 5052 2 port adapter
usbcore: registered new interface driver ti_usb_3410_5052
drivers/usb/serial/ti_usb_3410_5052.c: TI USB 3410/5052 Serial Driver v0.9
usbcore: registered new interface driver uss720
drivers/usb/misc/uss720.c: v0.6:USB Parport Cable driver for Cables using the Lucent Technologies USS720 Chip
drivers/usb/misc/uss720.c: NOTE: this is a special purpose driver to allow nonstandard
drivers/usb/misc/uss720.c: protocols (eg. bitbang) over USS720 usb to parallel cables
drivers/usb/misc/uss720.c: If you just want to connect to a printer, use usblp instead
A dmesg vége:
usb 4-2: new full speed USB device using uhci_hcd and address 2
usb 4-2: configuration #1 chosen from 1 choice
ark3116 4-2:1.0: ark3116 converter detected
usb 4-2: ark3116 converter now attached to ttyUSB0
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
usb 4-2: USB disconnect, address 2
ark3116 ttyUSB0: ark3116 converter now disconnected from ttyUSB0
ark3116 4-2:1.0: device disconnected
usb 4-1: new full speed USB device using uhci_hcd and address 3
usb 4-1: configuration #1 chosen from 1 choice
ark3116 4-1:1.0: ark3116 converter detected
usb 4-1: ark3116 converter now attached to ttyUSB0
drivers/usb/serial/ark3116.c: can't set 0 baud, using 9600 instead
Az xgnokii kimenete:
[root@localhost ~]# xgnokii
Orphaned line: port = /dev/ttyUSB0
Orphaned line: model = 6510
LOG: debug mask is 0x1
(xgnokii:3108): Gtk-WARNING **: horizontal scrolling not implemented
(xgnokii:3108): Gtk-WARNING **: horizontal scrolling not implemented
phone instance config:
model: 6510
port_device: /dev/ttyUSB0
connection_type: 2
init_length: 0
serial_baudrate: 19200
serial_write_usleep: -1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script:
disconnect_script:
rfcomm_cn: 1
sm_retry: off
Connecting
Serial device: opening device /dev/ttyUSB0
Serial device: setting RTS to low and DTR to low
Serial device: setting RTS to high and DTR to high
Serial device: setting speed to 19200
Switching to FBUS mode
Serial device: setting speed to 115200
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Serial write: transmitter busy, waiting
Serial write: transmitter ready
Getting model...
Message sent: 0x1b / 0x0006
00 01 00 07 01 00 |
Serial write: transmitter busy, waiting
Serial write: transmitter ready
SM_Block: exiting the retry loop
Message sent: 0x1b / 0x0006
00 01 00 07 01 00 |
SM_Block: exiting the retry loop
A gnokiirc:
# This is a sample ~/.gnokiirc file. Copy it into your
# home directory and name it .gnokiirc.
# See http://wiki.gnokii.org/index.php/Config for working examples.
#
[global]
# Set port to the physical port used to connect to your phone.
# Linux version is:
port = /dev/ttyUSB0
#
# For MacOSX you will need something like:
# port = /dev/cu.USA28X1P1.1
#
# For Win32 you want to use:
# port = com1:
# or similiar.
#
# FreeBSD (probably NetBSD and OpenBSD too) use:
# port = /dev/cuaa0
#
# With Linux-IrDA you will want to use
# port = /dev/ircomm0
# or similiar.
#
# Use this setting also for the Bluetooth connection:
# port = aa:bb:cc:dd:ee:ff
# when using it with AT driver set it to:
# port = /dev/rfcomm0
# or similiar.
#
# For the Linux USB cables you will need one of the following settings (or
# similiar)
# port = /dev/ttyUSB0
# port = /dev/tts/USB0
# port = /dev/ttyACM0
# the last one will work only with AT driver. The correct setting should be
# given in the dmesg output.
# Set model to the model number of your phone. For the
# Symbian phones use:
# model = series60
# For other non-Nokia phones and when you want to use AT
# mode use:
# model = AT
# If you can't figure out what to put here read the FAQ.
# If it still doesn't help, consult gnokii-ml or #gnokii at freenode.
model = 6510
# There are few main models that should make use of the certain drivers.
# These are: 6110, 7110, 6510, 3110, 2110, 6160.
# Set IrDA device name.
# If you use irda connection you may want gnokii to autodetect the irda
# device it connects to. This is fine for most of the cases. if you have
# more than one device in range you may want to give manually the device
# name so gnokii correctly recognizes it. Use the name that you can see
# in the discovery log when the phone with infrared is in the range of
# your irda port.
# Note that you need to set this for each phone_ section separately. It
# isn't nested from the global section.
# irda_string = Nokia 6610i
# Initlength controls the number of characters sent to the
# phone during initialisation. You can either set it to
# the word "default" or a positive integer.
#
# You can try setting this value if you want to connect
# to the phone quicker. If you've never noticed the
# connection to be slow, it is suggested that you
# leave this alone. Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = default
# The type of the connection, for IR set this to infrared or irda.
# For the nk6110 driver only infrared is valid for the IrDA connection.
# See Docs/gnokii-ir-howto for more detailes on this.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
# If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
# you don't use model = AT) you may want to use 'dlr3p' value here.
# Note that it is recommended and currently the best way to use this
# cable with nk6510 driver.
connection = dlr3p
# With DKU-2 cable use the following setting if you want to libusb driver
# (recommended):
# connection = dku2libusb
# or the following setting if you want to use Linux kernel driver
# connection = dku2
# With DKU-5 cable use the following setting
# connection = dku5
# For Bluetooth and AT driver use the following setting
# connection = serial
# For other Bluetooth settings use
# connection = bluetooth
# For infrared connection with phones other than Nokia 6110/6130/6150 use
# connection = irda
# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = no
# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
serial_baudrate = 19200
# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"! FIXME: Model-driven autodetection
#serial_write_usleep = 10000
# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3 wires)
#handshake = software
# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1
# If you are using a bluetooth connection, you can specify the rfcomm
# channel number here. Default value is 1.
#rfcomm_channel = 1
# There may happen various timeouts during the communication with the phone.
# This parameter enables the retransmission policy. Ie. if the phone doesn't
# respond, we send the frame again. This happend mainly with the older
# phones. You may want to enable it when you see mysterious timeouts.
# Be very carefull with this option. It is suspected to cause phone breakage
# with new DCT4 phones (like Nokia 6100). By default it is switched off
# (sm_retry = 0)
#sm_retry = 1
# Run the specified script(s) right after opening and initializing the device
# and before any communication (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is run!
#connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
#disconnect_script =
# When sending SMS you can experience timeouts. This is the feature of the
# overloaded SMSCs. The phones waits for the response from the SMSC confirming
# that it received the short message. When the SMSC is DoSed with many requests
# it will take more time to get the response. Adjust it to your needs. The
# value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to wait
# forever.
smsc_timeout = 10
# Set bindir to point to the location of the various gnokiid binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii. Ensure you
# are in the gnokii group and that the group exists...
[gnokiid]
bindir = /usr/sbin/
# Any entries in the following two sections will be set as environment
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(8) script.
[connect_script]
TELEPHONE = 12345678
[disconnect_script]
# The following parameters control how libgnokii handle the debugging messages.
# Currently there are three categories: "debug" controls the libgnokii
# normal debug output, "rlpdebug" controls the debug output of the RLP
# subsystem, and "xdebug" is used by the xgnokii or smsd.
[logging]
# where to log the debug output (on: stderr, off: /dev/null)
debug = on
# where to log the rlp debug output (on: stderr, off: /dev/null)
rlpdebug = off
# where to log X debug output (on: stderr, off: /dev/null)
xdebug = off
Köszönöm: Zsolt