Dell R910 H200 Raid

Sziasztok.

A H700 vezérlőt kicseréltem H200-ra, mert ebben van IT mód és nekem most ez kell. Látszólag minden ok vele, viszont most 2 sas hdd-t tettem bele, és azokat vmiért nem tudom a rendszer alól kezelni. Mi lehet a gond? Az előző H700-as raid-ből kivettem mielőtt kártyát cseréltem. Egyébként azzal tökéletesen működött.

A smart látja, de a fdisk már nem. Alul pár log.

Köszönöm ha segítetek.

dmesg részlet:

[  250.181664] mpt2sas_cm0: handle(0xa) sas_address(0x5000c50096745221) port_type(0x1)
[  250.343515] scsi 2:0:3:0: Direct-Access     SEAGATE  ST1200MM0088     TT31 PQ: 0 ANSI: 6
[  250.343533] scsi 2:0:3:0: SSP: handle(0x000a), sas_addr(0x5000c50096745221), phy(16), device_name(0x0000000000000000)
[  250.343539] scsi 2:0:3:0: enclosure logical id (0x500065b37689abff), slot(0) 
[  250.343547] scsi 2:0:3:0: qdepth(254), tagged(1), scsi_level(7), cmd_que(1)
[  250.343783] scsi 2:0:3:0: Power-on or device reset occurred
[  250.348126] sd 2:0:3:0: Attached scsi generic sg1 type 0
[  250.348523]  end_device-2:0:3: add: handle(0x000a), sas_addr(0x5000c50096745221)
[  250.349126] sd 2:0:3:0: [sda] Spinning up disk...
[  251.382987] ..........ready
[  261.075087] sd 2:0:3:0: [sda] 2344225968 512-byte logical blocks: (1.20 TB/1.09 TiB)
[  261.075590] sd 2:0:3:0: [sda] Write Protect is off
[  261.075599] sd 2:0:3:0: [sda] Mode Sense: d7 00 10 08
[  261.076441] sd 2:0:3:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
[  261.077823] sd 2:0:3:0: [sda] Enabling DIF Type 2 protection
[  261.077831] sd 2:0:3:0: [sda] Preferred minimum I/O size 512 bytes
[  261.103220] mpt2sas_cm0: log_info(0x3112043b): originator(PL), code(0x12), sub_code(0x043b)
[  261.103326] scsi_io_completion_action: 24 callbacks suppressed
[  261.103339] sd 2:0:3:0: [sda] tag#1144 FAILED Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK cmd_age=0s
[  261.103350] sd 2:0:3:0: [sda] tag#1144 Sense Key : Illegal Request [current] 
[  261.103357] sd 2:0:3:0: [sda] tag#1144 Add. Sense: Logical block reference tag check failed
[  261.103364] sd 2:0:3:0: [sda] tag#1144 CDB: Read(32)
[  261.103370] sd 2:0:3:0: [sda] tag#1144 CDB[00]: 7f 00 00 00 00 00 00 18 00 09 20 00 00 00 00 00
[  261.103375] sd 2:0:3:0: [sda] tag#1144 CDB[10]: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 08
[  261.103379] blk_print_req_error: 24 callbacks suppressed
[  261.103383] protection error, dev sda, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 2
[  261.103484] buffer_io_error: 20 callbacks suppressed
[  261.103488] Buffer I/O error on dev sda, logical block 0, async page read

# smartctl -a /dev/sda
smartctl 7.3 2022-02-28 r5338 [x86_64-linux-6.5.11-4-pve] (local build)
Copyright (C) 2002-22, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Vendor:               SEAGATE
Product:              ST1200MM0088
Revision:             TT31
Compliance:           SPC-4
User Capacity:        1,200,243,695,616 bytes [1.20 TB]
Logical block size:   512 bytes
Formatted with type 2 protection
8 bytes of protection information per logical block
LU is fully provisioned
Rotation Rate:        10000 rpm
Form Factor:          2.5 inches
Logical Unit id:      0x5000c50096745223
Serial number:        S4019NAT
Device type:          disk
Transport protocol:   SAS (SPL-4)
Local Time is:        Fri Feb  9 17:24:23 2024 CET
SMART support is:     Available - device has SMART capability.
SMART support is:     Enabled
Temperature Warning:  Enabled

=== START OF READ SMART DATA SECTION ===
SMART Health Status: OK

Grown defects during certification <not available>
Total blocks reassigned during format <not available>
Total new blocks reassigned <not available>
Power on minutes since format <not available>
Current Drive Temperature:     32 C
Drive Trip Temperature:        60 C

Accumulated power on time, hours:minutes 33580:22
Manufactured in week 06 of year 2016
Specified cycle count over device lifetime:  10000
Accumulated start-stop cycles:  105
Specified load-unload count over device lifetime:  300000
Accumulated load-unload cycles:  348
Elements in grown defect list: 0

Vendor (Seagate Cache) information
  Blocks sent to initiator = 1446969937
  Blocks received from initiator = 2344423624
  Blocks read from cache and sent to initiator = 1675319229
  Number of read and write commands whose size <= segment size = 554430
  Number of read and write commands whose size > segment size = 2461

Vendor (Seagate/Hitachi) factory information
  number of hours powered up = 33580.37
  number of minutes until next internal SMART test = 57

Error counter log:
           Errors Corrected by           Total   Correction     Gigabytes    Total
               ECC          rereads/    errors   algorithm      processed    uncorrected
           fast | delayed   rewrites  corrected  invocations   [10^9 bytes]  errors
read:   2422111242        0         0  2422111242          0       4740.231           0
write:         0        0         0         0          0       1220.314           0
verify: 251604718        0         0  251604718          0     237217.557           0

Non-medium error count:      197

SMART Self-test log
Num  Test              Status                 segment  LifeTime  LBA_first_err [SK ASC ASQ]
     Description                              number   (hours)
# 1  Background short  Completed                  80       3                 - [-   -    -]
# 2  Reserved(7)       Completed                  64       3                 - [-   -    -]

Long (extended) Self-test duration: 7630 seconds [127.2 minutes]