Bootoloasnal read-only marad a /

Hi!
Tegnap ujrainditottam a gepem (nem szokasom amugy :D ), es bootolas kozben vmiert nem akarja rw-ra csatolni a gyoker filerendszert csak ro-ra. Utana meg persze bajlodik, hogy nem tud softlinkeket csinalni meg miegymas. Ezen a ponton be lehet lepni a rendszerbe (bar az init scripteket nem hajtotta vegre), igy megneztem hogy mi van az mtab-ban, es ott ugy jelzi, hogy rw-ban van csatolva a particio. :? Vajon mitol lehet ez? Nem valtoztattam semmit a rendszeren. A segitseget elore is koszi!

Jah, jut eszembe miutan behalt, kuldtem neki fsck-t, es az sem segitett :(

dmesg

[code:1:2330076574]
Linux version 2.6.13-suspend2-r4 (root@kleba) (gcc version 3.3.6 (Gentoo 3.3.6, ssp-3.3.6-1.0, pie-8.7.8)) #1 Fri Nov 4 03:38:42 CET 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fff0000 (usable)
BIOS-e820: 000000000fff0000 - 000000000fff3000 (ACPI NVS)
BIOS-e820: 000000000fff3000 - 0000000010000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
255MB LOWMEM available.
On node 0 totalpages: 65520
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 61424 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.2 present.
ACPI: RSDP (v000 Nvidia ) @ 0x000f6b60
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3000
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff3040
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x0fff79c0
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 10000000 (gap: 10000000:eec00000)
Built 1 zonelists
Kernel command line: root=/dev/hdb3 resume2=swap:/dev/hda2
Initializing CPU#0
CPU 0 irqstacks, hard=c0549000 soft=c0548000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1470.148 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 254424k/262080k available (3235k kernel code, 7084k reserved, 959k data, 164k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 2943.61 BogoMIPS (lpj=5887221)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0383fbff c1c3fbff 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 0383fbff c1c3fbff 00000000 00000020 00000000 00000000 00000000
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0c20)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb420, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050408
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
PCI: nForce2 C1 Halt Disconnect fixup
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APCE] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:00: ioport range 0x4000-0x407f could not be reserved
pnp: 00:00: ioport range 0x4080-0x40ff has been reserved
pnp: 00:00: ioport range 0x4400-0x447f has been reserved
pnp: 00:00: ioport range 0x4480-0x44ff could not be reserved
pnp: 00:00: ioport range 0x4200-0x427f has been reserved
pnp: 00:00: ioport range 0x4280-0x42ff has been reserved
pnp: 00:01: ioport range 0x5000-0x503f has been reserved
pnp: 00:01: ioport range 0x5100-0x513f has been reserved
PCI: Bridge: 0000:00:08.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
IO window: disabled.
MEM window: e4000000-e5ffffff
PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
vesafb: NVIDIA Corporation, NV31 Board - p141-3n , Chip Rev (OEM: NVIDIA)
vesafb: VBE version: 3.0
vesafb: protected mode interface info at c000:e780
vesafb: pmi: set display start = c00ce7b6, set palette = c00ce820
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
vesafb: hardware supports DDC2 transfers
vesafb: monitor limits: vf = 160 Hz, hf = 71 kHz, clk = 110 MHz
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 128x48
vesafb: framebuffer at 0xd0000000, mapped to 0xd0880000, using 24576k, total 131072k
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1])
ACPI: Thermal Zone [THRM] (56 C)
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
mice: PS/2 mouse device common for all mice
input: PC Speaker
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.35.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [LMAC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:04.0 to 64
input: AT Translated Set 2 keyboard on isa0060/serio0
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
eth0: forcedeth.c: subsystem: 0147b:1c02 bound to 0000:00:04.0
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y080L0, ATA DISK drive
hdb: Maxtor 6Y080L0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: Pioneer DVD-ROM ATAPIModel DVD-116 0122, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hda: cache flushes supported
hda: hda1 hda2 hda3
hdb: max request size: 128KiB
hdb: 160086528 sectors (81964 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(133)
hdb: cache flushes supported
hdb: hdb1 hdb2 hdb3
hdc: ATAPI 126X DVD-ROM drive, 256kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
i2c /dev entries driver
Advanced Linux Sound Architecture Driver Version 1.0.9b (Thu Jul 28 12:20:13 2005 UTC).
ACPI: PCI Interrupt Link [LACI] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [LACI] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:06.0 to 64
intel8x0_measure_ac97_clock: measured 52759 usecs
intel8x0: clocking to 47483
ALSA device list:
#0: NVidia nForce2 with ALC650D at 0xe6002000, irq 5
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Software Suspend Core.
Software Suspend Compression Driver loading.
Software Suspend Encryption Driver loading.
Software Suspend Swap Writer loading.
Software Suspend FileWriter loading.
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
Software Suspend 2.2-rc6: Swapwriter: Signature found.
Software Suspend 2.2-rc6: Suspending enabled.
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 164k freed
kjournald starting. Commit interval 5 seconds
Adding 500464k swap on /dev/hdb2. Priority:0 extents:1
Adding 500464k swap on /dev/hda2. Priority:0 extents:1
kjournald starting. Commit interval 5 seconds
EXT3 FS on hda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
[/code:1:2330076574]

Nemtom. Lattok benne vmi rendelleneset? Legyszi segitsetek mert livecd-vel nehez az elet... Egyebkent az az erdekes, hogy livecd-rol tok jol becsatolja a particiokat, es semmi gond nincs veluk.