[MEGOLDVA] SUN T5120

 ( hanzo | 2014. július 17., csütörtök - 13:55 )

Sziasztok!

Van egy SUN T5120-am de az ILOM jelszoval vedett es valszeg statikus ip cim van neki beallitva.
A kerdes az lenne, hogy hogy lehetne bejutni az ILOM-ba hogy hasznalhassam is a gepet! Mert ugy se vga kimenet se semmi rajta, mert ugy SPARK. Serial porton se ferk hozza sajnos. Az eredeti tulaj meg nem tudja mar a belepest az ILOM-ba sajnos. De az ip-re se emlexik mar.
Otletek?

MEGOLDAS:
A T5120 fedelet leszeded, a bal oldali pci-express kozepe fele van egy JUMPER azt kell az 1-2-es labra tenni! Bekapcsolod a gepet, serial porton csekkolod a boot-ot. Bebootol. Varakozol 5-10 percet es ki is irja hogy password reset succesfully.

Ennyi!

Hanzo

Hozzászólás megjelenítési lehetőségek

A választott hozzászólás megjelenítési mód a „Beállítás” gombbal rögzíthető.

reset-eld a kártyát (kis tűs gomb), és akkor visszaáll a gyári beállításokra. Soros porton úgy eléred.
9600/8/N/1
Ha jól emlékszem root/changeme

Szia!

Ilyen tus gombot nem talalunk sehol rajta sajnos.
Kozelebbi info esetleg?

--
http://szolarenergia.hu - A hálózat építést csak elkezdeni lehet, befejezni nem....

Hmm...

ftp://ftp.ocs.ru/pub/sun/Products/Systems/Niagara/PRESENTATIONS/T5120%20and%20T5220%20TTT.pdf
https://community.oracle.com/thread/2342754

"Lost 'root' password and ILOM config is reset using Motherboard Jumper J6801"
Tényleg lespórolták. Jumper.

De be tudsz OS konzolra menni, onnan is lehet. A boot folyamat közben be lehet ugrani az iLOM piszkáló menübe (hacsak nincs letiltva)

Az ott az u-boot. Valóban lehet törölni onnan az nvram-ot amiben tarolja az adatokat, viszont minden mast is (es lehet belole bazinagybazidraga levelnehezeket gyartani:))


// Happy debugging, suckers
#define true (rand() > 10)

Hi,

Magam meg nem probaltam, de probaltam valami hivatalos leirast talalni neked:

Resetting the ILOM and BIOS Passwords
This procedure causes the ILOM to reset the administration password and to clear
the BIOS password.
■ The administration (root) password becomes changeme.
■ The BIOS password is cleared, so that when you attempt to access the BIOS, it
does not prompt for a password.
This procedure requires changing a hardware jumper in your server enclosure. See
your service manual for details.

Ez csak emliti, hogy jumperelned kell.

Utana megtalaltam a MOS-on a kovetkezo doksit a dologrol:

How to Reset ILOM (2.0) Root Password on T5120/T5220/T5140/T5240 [Video] (Doc ID 1007050.1)

This section explains how to reset the ILOM root password for the Service Processor, running ILOM 2.0.
The Password Reset jumper referred to below is: J6801 for T5120 & T5220 / J10401 for T5140 & T5240.

Power down the host system (using the front panel power button) or if an SP admin account exists, you can alternately use that accounts ALOM Command Line Interface poweroff command. Unplug the system's power cord(s) Remove the system's top cover.

Implement all the usual anti-static-discharge methods, which for this procedure is:

Attach an antistatic wrist strap. When servicing or removing server components, attach an antistatic strap to your wrist and then to a metal area on the chassis Insert a Jumper (you provide the jumper) on Pins 1 & 2 of PJ6801 (or J10401). This Jumper is located at the Motherboard (near the edge of the Motherboard at rear of the system - center of the rear edge of the Motherboard).

Plug in the system's power cord(s). Press the front panel Power button to power on the system. You must power on the system to complete the reset. This is because the state of the PJ6801 (or J10401) jumper cannot be determined without the host CPU running. The SP root password will be reset to the default changeme.
Log in as root into the SP, using any available method - ssh or a Web Browser to the SP's network management port or via tip-hardware or a terminal server to the SP's serial management port. Password to use is changeme. That is simply to see if the changeme password works.

Power down the system using the front panel. Unplug the system's power cord(s). Again using the usual anti-static-discharge methods. Remove the PJ6801 jumper. You must remove the PJ6801 (or J10401) jumper after resetting the password, or the password will be reset every time the SP is reset (e.g. at power up).
Replace the system's top cover. Plug in the system's power cord(s). If the system administrator would like the SP's root account password changed to something other than changeme, then you can change the root password using the usual SP's root account's Command Line User Interface command.

Whether or not the SP's root account password is to be changed to something different than changeme after the top cover has been reinstalled and the system's power cord(s) plugged-in, if the system administrator would like the Host powered-up, that can be done using the front panel power button or via a login to the SP's root or admin accounts and the appropriate START or power on, respectively, may be used.

Ha pedig igy se egyertelmu, akkor van 1 videojuk arrol, hol es mit is kell tenni:

https://support.oracle.com/epmos/main/downloadattachmentprocessor?attachid=1007050.1:PASSWORD_RESET&clickstream=yes

Remelem tudtam segiteni.

MiszterX -- http://blog.xorp.hu

Gyorsabb voltam kolléga ;-)

Oreg ember nem gyors vonat :)

MiszterX -- http://blog.xorp.hu