[megoldva] wpa_supplicant+ndiswrapper+Dell Inspiron 1520

Sziasztok! Szeretnék segítséget kérni. 5 napja szenvedek és nem akarja a jót. Wifi-vel szeretnék 1 WPA-PSK TKIP titkosított látható routerre csatlakozni. Ám sajnos nem akarja. Google és gentoo-forums sem találtam megoldást.
A szükséges infók:

saddam # dmesg | tail
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
ADDRCONF(NETDEV_UP): wlan0: link is not ready
eth0: no IPv6 routers present
ADDRCONF(NETDEV_UP): eth0: link is not ready
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
eth0: no IPv6 routers present
ADDRCONF(NETDEV_UP): wlan0: link is not ready

saddam #cat /etc/wpa_supplicant/wpa_supplicant.conf
# This is a network block that connects to any unsecured access point.
# We give it a low priority so any defined blocks are preferred.
network={
ssid="ronhks"
proto=WPA
key_mgmt=WPA-PSK
#pairwise=TKIP
#group=TKIP
psk=****34909109b42725****c90b92a********22e34aa*****2d38eab5bdb
priority=5
}
network={

key_mgmt=NONE
priority=-9999999
}

saddam #cat /etc/conf.d/net
# This blank configuration will automatically use DHCP for any net.*
# scripts in /etc/init.d. To create a more complete configuration,
# please review /etc/conf.d/net.example and save your configuration
# in /etc/conf.d/net (this file :]!)
#The end of this file:
modules=( "wpa_supplicant" ) #To you the wpa_supplicant program
wpa_supplicant_wlan0="-Dndiswrapper" #To use ndiswrapper
#essid_wlan0="saddam"
#mode_wlan0="auto" #You can change the following settings, read about
#channel_wlan0="3" #them in /etc/conf.d/wireless.example
#key_saddam="s:text_pass!"
#sleep_scan_wlan0="1"
#sleep_associate_wlan0="2"
config_wlan0=( "dhcp" )
#dhcpcd_wlan0="-t 5"

saddam # iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

sit0 no wireless extensions.

wlan0 IEEE 802.11g ESSID:off/any
Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power:24 dBm
RTS thr:2347 B Fragment thr:2346 B
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

[b]saddam # /etc/init.d/net.wlan0 restart
* Stopping wlan0
* Bringing down wlan0
* Shutting down wlan0 ... [ ok ]
* Stopping wpa_cli on wlan0 ... [ ok ]
* Stopping wpa_supplicant on wlan0 ... [ ok ]
* Starting wlan0
* Starting wpa_supplicant on wlan0 ... [ ok ]
* Starting wpa_cli on wlan0 ... [ ok ]
* Backgrounding ...

saddam # wpa_supplicant -v
wpa_supplicant v0.5.7
Copyright (c) 2003-2006, Jouni Malinen and contributors

saddam # ndiswrapper -v
version: 1.51
vermagic: 2.6.23.1 SMP mod_unload CORE2

saddam #uname -r
2.6.23.1

saddam #lspci | tail
0c:00.0 Network controller: Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 01)

és dhcpcd pedig time_out-l elszall :(

Van vkinek vmi ötlete?
a dmesg uzit nem tudom megoldani pedig ott lesz a hiba sztem.

Előre is kösznöm a segítséget