Mindenfele segítség

Fórumok

Mindenfele segítség

Hozzászólások

Sziasztok!

Nekem az a gondom, hogy nem ismeri fel a dvd írómat!
hiába teszk bele cd-t vagy dvd-t nem mountolja be.

LG 4160 az íróm
AMD 3100 Sempron Asus 9550GE
Kezdőként egy kissé nehéz.
se a mediában, se a dev ben nem látom...

[quote:1a00d1b2af="Anix"]
a kde vezérlőpultban userként nem látok semmi másat csak a KDE komponenseket, amiben csak az erőforrás beállítása van. eddig voltak perifériák, témák, rendszeradminisztráció stb. de most semmi.

- Netről frissítetted? Az uhu hivatalos serverén lévő csomagok néha elég szarok. Pl. az utsó 1.1-eshez való HPIJS csomagba 1 azaz egy darab nyomtató támogatása volt befordítva (gondolom a maintainer sajátja) :P
(mondjuk a fenti állítás igaz a CD-n lévőkre is, pl. 1.1.1 vs ALSA :P)
- Eddig is ezt a CD-t használtad? (ld előbbi kérdés vége...)
- ~/.kde könyvtár maradt a régi, vagy ez teljesen szűz telepítés volt? A KDE hajlamos régi verziójú konfigfájlok esetén az összegabalyodásra, ha ez a helyzet, töröld a ~/.kde-t teljesen.

[quote:1a00d1b2af="Anix"]
a másik probléma, hogy 1280x1024 felbontást használok, de a k3b valamiért kisebb felbontással megy és óriási ikonok vannak benne. azelőtt ez is ment rendesen.

Hmm... Érdekes, erről küldhetnél scrshotot...

[quote:1a00d1b2af="aattis"]Sziasztok!
Nekem az a gondom, hogy nem ismeri fel a dvd írómat!
hiába teszk bele cd-t vagy dvd-t nem mountolja be.
LG 4160 az íróm
se a mediában, se a dev ben nem látom...

Adj ki egy 'find /dev -iname cd' parancsot!
Néha, pl. nekem pendrive-nál nem rakta ki a symlinket a devfs a /dev alá, de a /dev/scsi mélyén (4. alkönyvtár) ott volt a device fájl...
A mountolással nemtok mit kezdeni, én amíg Uhut használtam azonnal tiltottam az automountot.

Hello!
nem akartam új topicot nyitni, csak ide leírom problémáimat.
eddig a gépemen volt windóz + uhu 1.2 na nost döntöttem, hogy teljesen felesleges a win, ezért full formatálás. uhu-t újratelepítettem és következőket tapasztaltam:
a kde vezérlőpultban userként nem látok semmi másat csak a KDE komponenseket, amiben csak az erőforrás beállítása van. eddig voltak perifériák, témák, rendszeradminisztráció stb. de most semmi.
a másik probléma, hogy 1280x1024 felbontást használok, de a k3b valamiért kisebb felbontással megy és óriási ikonok vannak benne. azelőtt ez is ment rendesen.

Hi!

Tudna nekem valaki segíteni abban, hogy honnan tudok UHU installt letölteni?

Thx,
Zavy

Üdv!

Ha csak a lényegre vagy kíváncsi:

www.uhulinux.hu
letöltés menüpont...

Ha a véleményemre is:

Ha nem ölsz bele energiát abba amit meg akarsz
csinálni, nagy valószínűséggel mások sem fognak
segíteni benne. Kis keresgéléssel magad is megtalálhattad
volna. (Csak hogy a legalapabbat írjam: google
+ "uhu linux letöltés")
Ha a linux világában szeretnél mocorogni, akkor
igencsak szükség lesz a kezdeményezőképességedre,
meg a kutatómunkára. A fórumokon is hamarabb
kaphatsz segítséget, ha látják, hogy foglalkoztál
a dologgal, és leírod, hogy mire jutottál, mielőtt
másokhoz furdultál.
Nem tudom milyen célból szeretnél uhu linuxot,
de ha hiányzik belőled a tanulás képessége és
az igyekezet, akkor nem sok sikert jósolok neked
ezen a vonalon.
Remélem nem sértettelek meg azzal, amit leírtam.
Szándékomban legalábbis nem állt.
Nem ismerlek, csak a kérdésedből következtettem
ezekre a dolgokra. (Tévedni ugyebár pedig mindenki
tévedhet... :-) )

Hali,

Dwarf

Hali!

Köszi a segítséget. Az az igazság, hogy az UHU nem nekem kell. Nem is igazán érdekel. Más kért meg, hogy próbáljam neki megszerezni. És igazándiból ez tűnt a legkisebb energiabefektetésnek, hogy írok egy amúgyis jól működő fórumra, mint hogy én kezdek el keresgetni. :)
Gondoltam aki úgyis tud, az segít.

Köszi még1x.

Zavy

azért egy googlet megért volna... :wink:

Lehet, de így sem fájt senkinek ;) HUP-on néztem, de ott nem volt.

Zavy

[quote:b0c3b0727e="zavy"]Lehet, de így sem fájt senkinek ;) HUP-on néztem, de ott nem volt.

Zavy

A HUP-on igazabol nincs letoltes funkcio. Neha, nagy rohamok idejere kiteszek egy-egy kelendobb cuccot par napra, mert savszelesseg az van. Igazabol ha stuffokat keresel, akkor az FTP szerveren kellene korulnezni: FTP.FSN.HU (uhu nincs - AFAIK)

[quote:a34b774da2="trey"][quote:a34b774da2="zavy"]Lehet, de így sem fájt senkinek ;) HUP-on néztem, de ott nem volt.

Zavy

A HUP-on igazabol nincs letoltes funkcio. Neha, nagy rohamok idejere kiteszek egy-egy kelendobb cuccot par napra, mert savszelesseg az van. Igazabol ha stuffokat keresel, akkor az FTP szerveren kellene korulnezni: FTP.FSN.HU (uhu nincs - AFAIK)

ThIKC

[quote:5e0b92b0f1="vmiklos"]azért egy googlet megért volna... :wink:

Kegyetlen vagy. :D

[quote:9e296dfcd3="balage2"][quote:9e296dfcd3="vmiklos"]azért egy googlet megért volna... :wink:

Kegyetlen vagy. :D

Jah, mint az élet ;););)

[quote:c4ca253626="vmiklos"]azért egy googlet megért volna... :wink:

I will use Google before asking dumb questions next time. :)

Zavy

Helló !

Nem akarok új topicot nyitni , nem tudjátok hogy 1.1 -ben a csomagkezelővel letöltött gdesklets miért áll le ??
shell-ben >>

"./gdesklets shell
Could not connect to gnome-session. GNOME session management will not be
available for this application.
gDesklets 0.25.1
"

Külön ablakként megnyilik :

"Could not add display

The display could not be added because the file does not exist."

Kösz

Sajnos nem láttam még ezt a gdesklets-t :-)

Mi ez a "gdesklets shell"?
Valami ilyesmit kellene megpróbálni:
'gdesklets shell.display'

Sziasztok!

Kezdő linuxos vagyok, és problémám akadt a hanggal. Nincs. Ebben szeretnék segítséget kérni.
Integrált Creative AWE 64D hangkártyám van.

[17179569.184000] Linux version 2.6.17.6-10 (uhubuild@build) (gcc version 3.4.6) #1 SMP Mon Aug 21 11:06:08 CEST 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000000a000000 (usable)
[17179569.184000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 160MB LOWMEM available.
[17179569.184000] On node 0 totalpages: 40960
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] Normal zone: 36864 pages, LIFO batch:7
[17179569.184000] DMI not present or invalid.
[17179569.184000] ACPI: Unable to locate RSDP
[17179569.184000] Allocating PCI resources starting at 10000000 (gap: 0a000000:f4c00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: lang=hu
[17179569.184000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[17179569.184000] mapped APIC to ffffd000 (01149000)
[17179569.184000] Enabling fast FPU save and restore... done.
[17179569.184000] Initializing CPU#0
[17179569.184000] PID hash table entries: 1024 (order: 10, 4096 bytes)
[ 0.000000] Detected 488.664 MHz processor.
[ 61.864412] Using tsc for high-res timesource
[ 61.866034] Console: colour VGA+ 80x25
[ 61.866632] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 61.867524] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 61.893822] Memory: 126104k/163840k available (3154k kernel code, 37196k reserved, 1276k data, 292k init, 0k highmem)
[ 61.972267] Calibrating delay using timer specific routine.. 978.82 BogoMIPS (lpj=1957647)
[ 62.135876] kdb version 4.4 by Keith Owens, Scott Lurndal. Copyright SGI, All Rights Reserved
[ 62.136141] Security Framework v1.0.0 initialized
[ 62.136251] Mount-cache hash table entries: 512
[ 62.136725] CPU: After generic identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 62.136761] CPU: After vendor identify, caps: 0183f9ff 00000000 00000000 00000000 00000000 00000000 00000000
[ 62.136806] CPU: L1 I cache: 16K, L1 D cache: 16K
[ 62.136818] CPU: L2 cache: 128K
[ 62.136831] CPU: After all inits, caps: 0183f9ff 00000000 00000000 00000040 00000000 00000000 00000000
[ 62.136859] Intel machine check architecture supported.
[ 62.136875] Intel machine check reporting enabled on CPU#0.
[ 62.136936] Checking 'hlt' instruction... OK.
[ 62.152336] SMP alternatives: switching to UP code
[ 62.153372] Freeing SMP alternatives: 24k freed
[ 62.154072] checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
[ 62.581464] Freeing initrd memory: 30328k freed
[ 62.581498] CPU0: Intel Celeron (Mendocino) stepping 05
[ 62.581522] SMP motherboard not detected.
[ 62.581533] Local APIC not detected. Using dummy APIC emulation.
[ 62.581887] Brought up 1 CPUs
[ 62.581970] migration_cost=0
[ 62.583336] Time: 22:24:10 Date: 02/17/107
[ 62.583506] NET: Registered protocol family 16
[ 62.583671] EISA bus registered
[ 62.584847] PCI: PCI BIOS revision 2.10 entry at 0xfdba1, last bus=1
[ 62.584862] Setting up standard PCI resources
[ 62.588418] ACPI: Subsystem revision 20060127
[ 62.588429] ACPI: Interpreter disabled.
[ 62.588444] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 62.588506] pnp: PnP ACPI: disabled
[ 62.588519] PnPBIOS: Scanning system for PnP BIOS support...
[ 62.588642] PnPBIOS: Found PnP BIOS installation structure at 0xc00f8070
[ 62.588659] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0x785e, dseg 0xf0000
[ 62.590562] PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
[ 62.590878] PCI: Probing PCI hardware
[ 62.590895] PCI: Probing PCI hardware (bus 00)
[ 62.591564] PCI quirk: region 6100-613f claimed by PIIX4 ACPI
[ 62.591579] PCI quirk: region 5f00-5f0f claimed by PIIX4 SMB
[ 62.591943] Boot video device is 0000:01:00.0
[ 62.592965] PCI: Using IRQ router PIIX/ICH [8086/7110] at 0000:00:07.0
[ 62.595057] TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca)
[ 62.595271] pnp: 00:08: ioport range 0x6100-0x613f has been reserved
[ 62.595287] pnp: 00:08: ioport range 0x5f00-0x5f0f has been reserved
[ 62.595301] pnp: 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 62.595315] pnp: 00:08: ioport range 0xcf8-0xcff has been reserved
[ 62.595761] PCI: Bridge: 0000:00:01.0
[ 62.595774] IO window: d000-dfff
[ 62.595792] MEM window: ff900000-ff9fffff
[ 62.595807] PREFETCH window: eea00000-f6afffff
[ 62.595944] NET: Registered protocol family 2
[ 62.628667] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 62.629472] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 62.629917] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[ 62.630158] TCP: Hash tables configured (established 8192 bind 4096)
[ 62.630171] TCP reno registered
[ 62.630710] Machine check exception polling timer started.
[ 62.630744] cpufreq: No nForce2 chipset.
[ 62.630995] IA-32 Microcode Update Driver: v1.14
[ 62.631022] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.17)
[ 62.633344] Total HugeTLB memory allocated, 0
[ 62.633714] VFS: Disk quotas dquot_6.5.1
[ 62.633813] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 62.634161] squashfs: version 3.0 (2006/03/15) Phillip Lougher
[ 62.634464] NTFS driver 2.1.27 [Flags: R/W].
[ 62.634580] EFS: 1.0a - http://aeschi.ch.eu.org/efs/
[ 62.634608] JFFS version 1.0, (C) 1999, 2000 Axis Communications AB
[ 62.634654] JFFS2 version 2.2. (NAND) (SUMMARY) (C) 2001-2003 Red Hat, Inc.
[ 62.634969] QNX4 filesystem 0.2.3 registered.
[ 62.635109] JFS: nTxBlock = 1223, nTxLock = 9788
[ 62.638800] SGI XFS with ACLs, security attributes, large block numbers, no debug enabled
[ 62.639540] SGI XFS Quota Management subsystem
[ 62.639571] BeFS version: 0.9.3
[ 62.639758] Initializing Cryptographic API
[ 62.639780] io scheduler noop registered
[ 62.639826] io scheduler anticipatory registered (default)
[ 62.639858] io scheduler deadline registered
[ 62.639937] io scheduler cfq registered
[ 62.639973] Limiting direct PCI/PCI transfers.
[ 62.640731] isapnp: Scanning for PnP cards...
[ 62.751689] pnp: SB audio device quirk - increasing port range
[ 62.751891] isapnp: Card 'Creative ViBRA16X PnP'
[ 62.751904] isapnp: 1 Plug & Play card detected total
[ 62.755127] Real Time Clock Driver v1.12ac
[ 62.755290] Non-volatile memory driver v1.2
[ 62.755301] Linux agpgart interface v0.101 (c) Dave Jones
[ 62.755616] agpgart: Detected an Intel 440LX Chipset.
[ 62.763021] agpgart: AGP aperture is 64M @ 0xf8000000
[ 62.763850] RAMDISK driver initialized: 8 RAM disks of 32768K size 1024 blocksize
[ 62.764344] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 62.764362] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 62.764554] PIIX4: IDE controller at PCI slot 0000:00:07.1
[ 62.764607] PIIX4: chipset revision 1
[ 62.764617] PIIX4: not 100% native mode: will probe irqs later
[ 62.764646] ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
[ 62.764688] ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
[ 62.764720] Probing IDE interface ide0...
[ 62.812136] hda: SAMSUNG SP0802N, ATA DISK drive
[ 62.924098] hdb: HL-DT-ST GCE-8526B, ATAPI CD/DVD-ROM drive
[ 62.932424] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 62.932639] Probing IDE interface ide1...
[ 63.021389] Probing IDE interface ide1...
[ 63.475937] hda: max request size: 512KiB
[ 63.477259] hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(33)
[ 63.477508] hda: cache flushes supported
[ 63.477674] hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
[ 63.543978] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
[ 63.543994] PNP: PS/2 controller doesn't have AUX irq; using default 12
[ 63.545449] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 63.545584] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 63.545708] mice: PS/2 mouse device common for all mice
[ 63.545967] input: PC Speaker as /class/input/input0
[ 63.546101] wistron_btns: System unknown
[ 63.546446] device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
[ 63.546639] EISA: Probing bus 0 at eisa.0
[ 63.547104] NET: Registered protocol family 1
[ 63.547168] Using IPI No-Shortcut mode
[ 63.547177] Suspend2 Core.
[ 63.547258] Suspend2 Compression Driver loading.
[ 63.547277] Suspend2 Encryption Driver loading.
[ 63.547302] Suspend2 Swap Writer loading.
[ 63.547325] Suspend2 FileWriter loading.
[ 63.547424] Magic number: 15:965:451
[ 63.547461] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 63.547879] RAMDISK: squashfs filesystem found at block 0
[ 63.547905] RAMDISK: Loading 30325KiB [1 disk] into ram disk... |/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\done.
[ 64.054788] Suspend2 2.2.6: You need to use a resume2= command line parameter to tell Suspend2 where to look for an image.
[ 64.054827] Suspend2 2.2.6: Resume2 parameter is empty. Suspending will be disabled.
[ 64.054843] Suspend2 2.2.6: Missing or invalid storage location (resume2= parameter). Please correct and rerun lilo (or equivalent) before suspending.
[ 64.056851] VFS: Mounted root (squashfs filesystem) readonly.
[ 64.058113] Freeing unused kernel memory: 292k freed
[ 67.310935] hdb: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
[ 67.310974] Uniform CD-ROM driver Revision: 3.20
[ 67.322754] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 67.342327] 8139too Fast Ethernet driver 0.9.27
[ 67.342512] PCI: Found IRQ 10 for device 0000:00:12.0
[ 67.343062] eth0: RealTek RTL8139 at 0xca962f00, 00:40:f4:d0:fb:b3, IRQ 10
[ 67.343076] eth0: Identified 8139 chip type 'RTL-8100B/8139D'
[ 67.413955] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[ 67.826754] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 68.082676] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 68.089630] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 68.089964] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 68.807847] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 68.865123] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 68.867958] usbcore: registered new driver usbfs
[ 68.868080] usbcore: registered new driver hub
[ 68.894551] USB Universal Host Controller Interface driver v3.0
[ 68.894839] PCI: Found IRQ 9 for device 0000:00:07.2
[ 68.894900] uhci_hcd 0000:00:07.2: UHCI Host Controller
[ 68.895185] uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
[ 68.895254] uhci_hcd 0000:00:07.2: irq 9, io base 0x0000ef80
[ 68.895635] usb usb1: configuration #1 chosen from 1 choice
[ 68.895758] hub 1-0:1.0: USB hub found
[ 68.895798] hub 1-0:1.0: 2 ports detected
[ 69.274144] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 69.432366] usb 1-1: configuration #1 chosen from 1 choice
[ 69.674032] usb 1-2: new low speed USB device using uhci_hcd and address 3
[ 69.841160] usb 1-2: configuration #1 chosen from 1 choice
[ 70.019173] input: HID 1267:0103 as /class/input/input1
[ 70.019293] input: USB HID v1.10 Keyboard [HID 1267:0103] on usb-0000:00:07.2-1
[ 70.037258] input: HID 1267:0103 as /class/input/input2
[ 70.037382] input: USB HID v1.10 Device [HID 1267:0103] on usb-0000:00:07.2-1
[ 70.052084] input: USB Mouse as /class/input/input3
[ 70.052230] input: USB HID v1.00 Mouse [USB Mouse] on usb-0000:00:07.2-2
[ 70.052281] usbcore: registered new driver usbhid
[ 70.052297] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 71.149435] Floppy drive(s): fd0 is 1.44M
[ 71.169266] FDC 0 is a post-1991 82077
[ 71.231699] Capability LSM initialized
[ 71.304969] Databook TCIC-2 PCMCIA probe: not found.
[ 71.390715] loop: loaded (max 8 devices)
[ 72.211692] NET: Registered protocol family 10
[ 72.212113] lo: Disabled Privacy Extensions
[ 72.212499] IPv6 over IPv4 tunneling driver
[ 514.548845] hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > hda3
[ 562.295330] hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > hda3
[ 565.997444] hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 > hda3
[ 576.215301] kjournald starting. Commit interval 5 seconds
[ 576.215631] EXT3 FS on hda10, internal journal
[ 576.215653] EXT3-fs: mounted filesystem with ordered data mode.
[ 579.653232] cdrom: hdb: mrw address space DMA selected
[ 585.320089] ISO 9660 Extensions: Microsoft Joliet Level 3
[ 585.322341] ISO 9660 Extensions: RRIP_1991A
[ 2114.639307] aty128fb: Found Intel x86 BIOS ROM Image
[ 2114.639322] aty128fb: Rage128 BIOS located
[ 2114.639341] aty128fb: Rage128 TF Ultra AGP [chip rev 0x4] 32M 128-bit SDR SGRAM (1:1)
[ 2114.639545] fb0: ATY Rage128 frame buffer device on Rage128 TF Ultra AGP
[ 2114.639863] aty128fb: Rage128 MTRR set to ON
[ 2114.708774] piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
[ 2114.733727] pnp: Device 01:01.01 activated.
[ 2114.766724] gameport: NS558 PnP Gameport is pnp01:01.01/gameport0, io 0x201, speed 877kHz
[ 2115.870755] lp: driver loaded but no devices found
[ 2116.066706] ppdev: user-space parallel port driver
[ 2116.078925] parport: PnPBIOS parport detected.
[ 2116.079018] parport0: PC-style at 0x378 (0x778), irq 7, dma 0 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[ 2116.174881] lp0: using parport0 (interrupt-driven).
[ 2117.049034] microcode: CPU0 updated from revision 0x0 to 0x3, date = 05051999
[ 2118.817223] fuse init (API version 7.6)
[ 2119.062560] EXT3 FS on hda10, internal journal
[ 2129.207235] ReiserFS: hda9: found reiserfs format "3.6" with standard journal
[ 2129.677243] ReiserFS: hda9: using ordered data mode
[ 2129.689335] ReiserFS: hda9: journal params: device hda9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 2129.697077] ReiserFS: hda9: checking transaction log (hda9)
[ 2129.734835] ReiserFS: hda9: Using r5 hash to sort names
[ 2130.141348] kjournald starting. Commit interval 5 seconds
[ 2130.142211] EXT3 FS on hda8, internal journal
[ 2130.142241] EXT3-fs: mounted filesystem with ordered data mode.
[ 2130.878038] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 2131.678917] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 2132.325576] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 2134.104687] eth0: link down
[ 2134.104758] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2143.416265] [drm] Initialized drm 1.0.1 20051102
[ 2143.435606] [drm] Initialized r128 2.5.0 20030725 on minor 0
[ 2143.446553] agpgart: Found an AGP 1.0 compliant device at 0000:00:00.0.
[ 2143.446610] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[ 2143.446654] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode

[17179569.184000] Linux version 2.6.17.6-10 (uhubuild@build) (gcc version 3.4.6) #1 SMP Mon Aug 21 11:06:08 CEST 2006
[17179569.184000] BIOS-provided physical RAM map:
[17179569.184000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[17179569.184000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[17179569.184000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[17179569.184000] BIOS-e820: 0000000000100000 - 000000000a000000 (usable)
[17179569.184000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[17179569.184000] BIOS-e820: 00000000fffe0000 - 0000000100000000 (reserved)
[17179569.184000] 0MB HIGHMEM available.
[17179569.184000] 160MB LOWMEM available.
[17179569.184000] On node 0 totalpages: 40960
[17179569.184000] DMA zone: 4096 pages, LIFO batch:0
[17179569.184000] Normal zone: 36864 pages, LIFO batch:7
[17179569.184000] DMI not present or invalid.
[17179569.184000] ACPI: Unable to locate RSDP
[17179569.184000] Allocating PCI resources starting at 10000000 (gap: 0a000000:f4c00000)
[17179569.184000] Built 1 zonelists
[17179569.184000] Kernel command line: lang=hu
[17179569.184000] Local APIC disabled by BIOS -- you can enable it with "lapic"
[17179569.184000] mapped APIC to ffffd000 (01149000)
[17179569.184000] Enabling fast FPU save and restore... done.

igaz,hogy nem UHU hanem opensuse 10.2 de nem akartam miatta új topicot nyitni.
ebben szeretnék segítséget kérni.
köszönöm.