PVR 350 kartya

felintalaltam a hauppauge PVR 350-es kartyat egy ubuntura. elso nekifutasra minden stimmel, csak eppen egyik program sem latja a kartyat :(

itt van a dmesg kimenete:

[17179592.888000] ivtv: ==================== START INIT IVTV ====================
[17179592.888000] ivtv: version 0.7.1 (tagged release) loading
[17179592.888000] ivtv: Linux version: 2.6.17-10-generic SMP mod_unload 586 REGPARM gcc-4.1
[17179592.888000] ivtv: In case of problems please include the debug info between
[17179592.888000] ivtv: the START INIT IVTV and END INIT IVTV lines, along with
[17179592.888000] ivtv: any module options, when mailing the ivtv-users mailinglist.
[17179592.944000] 8139too Fast Ethernet driver 0.9.27
[17179593.192000] eth0: forcedeth.c: subsystem: 01695:1000 bound to 0000:00:04.0
[17179593.192000] ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 21
[17179593.192000] ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 21 (level, high) -> IRQ 193
[17179593.192000] PCI: Setting latency timer of device 0000:00:06.0 to 64
[17179593.512000] intel8x0_measure_ac97_clock: measured 54738 usecs
[17179593.512000] intel8x0: clocking to 47483
[17179593.512000] ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
[17179593.512000] ACPI: PCI Interrupt 0000:01:0b.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 217
[17179593.512000] eth1: RealTek RTL8139 at 0xe0aaa000, 00:04:61:4d:37:d2, IRQ 217
[17179593.512000] eth1: Identified 8139 chip type 'RTL-8101'
[17179593.512000] ivtv0: Autodetected Hauppauge WinTV PVR-350 card (cx23415 based)
[17179593.520000] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
[17179593.520000] ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 225
[17179593.520000] ivtv0: Unreasonably low latency timer, setting to 64 (was 32)
[17179593.568000] Floppy drive(s): fd0 is 1.44M
[17179593.588000] FDC 0 is a post-1991 82077
[17179593.872000] tveeprom 2-0050: Hauppauge model 48139, rev K257, serial# 2895209
[17179593.872000] tveeprom 2-0050: tuner model is Philips FM1216 ME MK3 (idx 57, type 38)
[17179593.872000] tveeprom 2-0050: TV standards PAL(B/G) PAL(I) SECAM(L/L') PAL(D/D1/K) (eeprom 0x74)
[17179593.872000] tveeprom 2-0050: audio processor is MSP4418 (idx 25)
[17179593.872000] tveeprom 2-0050: decoder processor is SAA7115 (idx 19)
[17179593.872000] tveeprom 2-0050: has radio, has IR remote
[17179593.924000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[17179594.092000] parport: PnPBIOS parport detected.
[17179594.092000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[17179594.264000] eth0: no link during initialization.
[17179594.356000] usbcore: registered new driver hiddev
[17179594.368000] input: Chicony USB Wireless HID Receiver as /class/input/input0
[17179594.368000] input: USB HID v1.10 Keyboard [Chicony USB Wireless HID Receiver] on usb-0000:00:02.0-1
[17179594.464000] tuner 2-0061: chip found @ 0xc2 (ivtv i2c driver #0)
[17179594.680000] tda9887 2-0043: chip found @ 0x86 (ivtv i2c driver #0)
[17179594.732000] input: PC Speaker as /class/input/input1
[17179594.820000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 5 if 0 alt 0 proto 2 vid 0x04E8 pid 0x3268
[17179594.820000] drivers/usb/class/usblp.c: Disabling reads from problem bidirectional printer on usblp0
[17179594.828000] drivers/usb/class/usblp.c: usblp1: USB Unidirectional printer dev 6 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0604
[17179594.868000] saa7115 2-0021: saa7115 found @ 0x42 (ivtv i2c driver #0)
[17179595.096000] saa7127 2-0044: saa7129 found @ 0x88 (ivtv i2c driver #0)
[17179595.132000] msp3400 2-0040: MSP4418G-B3 found @ 0x80 (ivtv i2c driver #0)
[17179595.132000] msp3400 2-0040: MSP4418G-B3 supports nicam and radio, mode is autodetect and autoselect
[17179595.332000] NET: Registered protocol family 17
[17179595.932000] ivtv0: loaded v4l-cx2341x-enc.fw firmware (262144 bytes)
[17179596.004000] ivtv0: loaded v4l-cx2341x-dec.fw firmware (262144 bytes)
[17179596.228000] ivtv0: Encoder revision: 0x02050032
[17179596.236000] ivtv0: Decoder revision: 0x02020023
[17179596.236000] ivtv0: Allocate DMA encoder MPEG stream: 128 x 32768 buffers (4096KB total)
[17179596.236000] ivtv0: Allocate DMA encoder YUV stream: 161 x 12960 buffers (2048KB total)
[17179596.236000] ivtv0: Allocate DMA encoder VBI stream: 80 x 26208 buffers (2048KB total)
[17179596.236000] ivtv0: Allocate DMA encoder PCM audio stream: 455 x 4608 buffers (2048KB total)
[17179596.236000] ivtv0: Create encoder radio stream
[17179596.236000] ivtv0: Allocate DMA decoder MPEG stream: 16 x 65536 buffers (1024KB total)
[17179596.236000] ivtv0: Allocate DMA decoder VBI stream: 512 x 2048 buffers (1024KB total)
[17179596.236000] ivtv0: Create decoder VOUT stream
[17179596.236000] ivtv0: Allocate DMA decoder YUV stream: 20 x 51840 buffers (1024KB total)
[17179596.320000] ivtv0: loaded v4l-cx2341x-init.mpg firmware (155648 bytes)
[17179596.428000] tuner 2-0061: type set to 38 (Philips PAL/SECAM multi (FM1216ME MK3))
[17179596.576000] ivtv0: Initialized Hauppauge WinTV PVR-350, card #0

----

tvtime pld. azt irja ki, hogy nem tudja megnyitni a /dev/video0-t...

valami otlet????