ABIT AN7 sensorainak használata

Lehet hogy a TV tunerem kavar be?

[quote:4fc697253c="xbit"][quote:4fc697253c="borz"]Lehet hogy a TV tunerem kavar be?

nem valoszinu. nallam abit kv7 es es cx8 as tuner szepen megy.
igaz hogy mindketto mas mint nallad, dehat rokonok...
eloszoris kernel verziod?

kernel verzióm: 2.6.9
A kernelbe a kovetkezok vannak modulba forditva:

[code:1:4fc697253c]
/lib/modules/2.6.9/kernel/drivers/i2c/algos/i2c-algo-bit.ko
/lib/modules/2.6.9/kernel/drivers/i2c/algos/i2c-algo-pcf.ko
/lib/modules/2.6.9/kernel/drivers/i2c/busses/i2c-isa.ko
/lib/modules/2.6.9/kernel/drivers/i2c/busses/i2c-nforce2.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/adm1021.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/adm1025.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/adm1031.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/asb100.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/ds1621.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/eeprom.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/fscher.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/gl518sm.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/it87.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/lm75.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/lm77.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/lm78.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/lm80.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/lm83.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/lm85.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/lm90.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/max1619.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/via686a.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/w83627hf.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/w83781d.ko
/lib/modules/2.6.9/kernel/drivers/i2c/chips/w83l785ts.ko
/lib/modules/2.6.9/kernel/drivers/i2c/i2c-core.ko
/lib/modules/2.6.9/kernel/drivers/i2c/i2c-dev.ko
/lib/modules/2.6.9/kernel/drivers/i2c/i2c-sensor.ko

[/code:1:4fc697253c]
Kell meg valamit ezeken kivul a kernelben engedelyezni?

[quote:51b18eda51="xbit"][quote:51b18eda51="borz"]kernel verzióm: 2.6.9

hmmm ugylatom minden a helyen van... disztrod lmsensors csomagjat hasznaltad ugye? 2.6.x nel mar nem kell kernelt patchelni, csak a userprogik kellenek...

megis probald esetleg ugy hogy a tuner modulokat levalsztod, de persze az i2c modulokat benthagyod.

van egy acpi nevu progi is, azt is nezegesd ki tudja e olvasni /proc bol

zsolt

kivettem a tuner moduljait, rebootoltam, majd az lsmodom:
[code:1:51b18eda51]
bash-2.05b# lsmod
Module Size Used by
snd_mixer_oss 17792 0
sg 29728 0
floppy 54224 0
md5 3840 1
ipv6 237952 10
rtc 10424 0
i2c_nforce2 5248 0
i2c_dev 7936 0
w83627hf 28584 0
eeprom 6816 0
i2c_sensor 3328 2 w83627hf,eeprom
snd_intel8x0 29096 1
snd_ac97_codec 68816 1 snd_intel8x0
snd_pcm 84872 1 snd_intel8x0
snd_timer 21380 1 snd_pcm
snd_page_alloc 7688 2 snd_intel8x0,snd_pcm
snd_mpu401_uart 6272 1 snd_intel8x0
snd_rawmidi 20260 1 snd_mpu401_uart
snd_seq_device 6536 1 snd_rawmidi
snd 47716 10 snd_mixer_oss,snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 7648 1 snd
forcedeth 14848 0
i2c_isa 1920 0
i2c_core 19216 6 i2c_nforce2,i2c_dev,w83627hf,eeprom,i2c_sensor,i2c_isa
sd_mod 13584 0
ehci_hcd 28292 0
usb_storage 64832 0
usbcore 102116 4 ehci_hcd,usb_storage
nvidia 4813268 12
3c59x 34984 0
ide_cd 37024 0
sr_mod 13860 0
scsi_mod 70080 4 sg,sd_mod,usb_storage,sr_mod
cdrom 36252 2 ide_cd,sr_mod
[/code:1:51b18eda51]

az acpi nem csinal semmit, ha csak siman beirom. kell parameterezni?
a distrom gentoo. en kulon nem patcheltem

[quote:028857ebdc="xbit"][quote:028857ebdc="borz"]az acpi nem csinal semmit, ha csak siman beirom. kell parameterezni?
a distrom gentoo. en kulon nem patcheltem

persze, probalgasd ;) pl `acpi -t` a hőt olvassa le.
gentoot nem ismerem...

zsolt

Jahh, hat ez nem sok jot mutat:

[code:1:028857ebdc]
bash-2.05b# acpi -t
Thermal 1: ok, 20.0 degrees C
[/code:1:028857ebdc]

Sziasztok!

Tudna segíteni valaki, hogy hogyan kell egy ABIT AN7-es alaplapot rávenni, hogy meg tudjam nézni a hőmérsékleteket, feszültségeket, stb...

Ok
felraktam a progit, csak nem vagyok biztos benne , hogy jol valaszoltam minden kerdesre.
Mivel van tv-tuner is a gepben, igy megprobaltam kihagyni azokat a reszeket.
Vegeredmeny:
[code:1:20d7250eb8]
bash-2.05b# sensors-detect

This program will help you determine which I2C/SMBus modules you need to
load to use lm_sensors most effectively. You need to have i2c and
lm_sensors installed before running this program.
Also, you need to be `root', or at least have access to the /dev/i2c/*
files, for most things.
If you have patched your kernel and have some drivers built in, you can
safely answer NO if asked to load some modules. In this case, things may
seem a bit confusing, but they will still work.

It is generally safe and recommended to accept the default answers to all
questions, unless you know what you're doing.

We can start with probing for (PCI) I2C or SMBus adapters.
You do not need any special privileges for this.
Do you want to probe now? (YES/no): y
Probing for PCI bus adapters...
Use driver `rivatv' for device 02:00.0: GeForce2 MX
Use driver `i2c-nforce2' for device 00:01.1: nVidia Corporation nForce2 SMBus (MCP)
Probe succesfully concluded.

We will now try to load each adapter module in turn.
Load `rivatv' (say NO if built into your kernel)? (YES/no): n
Load `i2c-nforce2' (say NO if built into your kernel)? (YES/no): y
Module loaded succesfully.
If you have undetectable or unsupported adapters, you can have them
scanned by manually loading the modules before running this script.

To continue, we need module `i2c-dev' to be loaded.
If it is built-in into your kernel, you can safely skip this.
i2c-dev is not loaded. Do you want to load it now? (YES/no): y
Module loaded succesfully.

We are now going to do the adapter probings. Some adapters may hang halfway
through; we can't really help that. Also, some chips will be double detected;
we choose the one with the highest confidence value in that case.
If you found that the adapter hung after probing a certain address, you can
specify that address to remain unprobed. That often
includes address 0x69 (clock chip).

Next adapter: SMBus nForce2 adapter at 5100 (Algorithm unavailable)
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x08

Next adapter: SMBus nForce2 adapter at 5000 (Algorithm unavailable)
Do you want to scan it? (YES/no/selectively): y
Client found at address 0x08
Client found at address 0x50
Probing for `SPD EEPROM'... Success!
(confidence 8, driver `eeprom')
Probing for `DDC monitor'... Failed!
Probing for `Maxim MAX6900'... Failed!
Client found at address 0x52
Probing for `SPD EEPROM'... Success!
(confidence 8, driver `eeprom')

Next adapter: bt878 #0 [sw] (Algorithm unavailable)
Do you want to scan it? (YES/no/selectively): n

Some chips are also accessible through the ISA bus. ISA probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. This is usually safe though.

Do you want to scan the ISA bus? (YES/no): y
Probing for `National Semiconductor LM78'
Trying address 0x0290... Failed!
Probing for `National Semiconductor LM78-J'
Trying address 0x0290... Failed!
Probing for `National Semiconductor LM79'
Trying address 0x0290... Failed!
Probing for `Winbond W83781D'
Trying address 0x0290... Failed!
Probing for `Winbond W83782D'
Trying address 0x0290... Failed!
Probing for `Winbond W83627HF'
Trying address 0x0290... Failed!
Probing for `Winbond W83697HF'
Trying address 0x0290... Failed!
Probing for `Silicon Integrated Systems SIS5595'
Trying general detect... Failed!
Probing for `VIA Technologies VT82C686 Integrated Sensors'
Trying general detect... Failed!
Probing for `VIA Technologies VT8231 Integrated Sensors'
Trying general detect... Failed!
Probing for `ITE IT8705F / IT8712F / SiS 950'
Trying address 0x0290... Failed!
Probing for `IPMI BMC KCS'
Trying address 0x0ca0... Failed!
Probing for `IPMI BMC SMIC'
Trying address 0x0ca8... Failed!

Some Super I/O chips may also contain sensors. Super I/O probes are
typically a bit more dangerous, as we have to write to I/O ports to do
this. This is usually safe though.

Do you want to scan for Super I/O sensors? (YES/no): y
Probing for `ITE 8702F Super IO Sensors'
Failed! (skipping family)
Probing for `Nat. Semi. PC87351 Super IO Fan Sensors'
Failed! (skipping family)
Probing for `SMSC 47B27x Super IO Fan Sensors'
Failed! (skipping family)
Probing for `VT1211 Super IO Sensors'
Failed! (0x52)
Probing for `Winbond W83627HF Super IO Sensors'
Success... found at address 0x0290
Probing for `Winbond W83627THF Super IO Sensors'
Failed! (0x52)
Probing for `Winbond W83637HF Super IO Sensors'
Failed! (0x52)
Probing for `Winbond W83697HF Super IO Sensors'
Failed! (0x52)
Probing for `Winbond W83697SF/UF Super IO PWM'
Failed! (0x52)
Probing for `Winbond W83L517D Super IO'
Failed! (0x52)

Do you want to scan for secondary Super I/O sensors? (YES/no): y
Probing for `ITE 8702F Super IO Sensors'
Failed! (skipping family)
Probing for `Nat. Semi. PC87351 Super IO Fan Sensors'
Failed! (skipping family)
Probing for `SMSC 47B27x Super IO Fan Sensors'
Failed! (skipping family)
Probing for `VT1211 Super IO Sensors'
Failed! (skipping family)

Now follows a summary of the probes I have just done.
Just press ENTER to continue:

Driver `eeprom' (should be inserted):
Detects correctly:
* Bus `SMBus nForce2 adapter at 5000' (Algorithm unavailable)
Busdriver `i2c-nforce2', I2C address 0x50
Chip `SPD EEPROM' (confidence: 8)
* Bus `SMBus nForce2 adapter at 5000' (Algorithm unavailable)
Busdriver `i2c-nforce2', I2C address 0x52
Chip `SPD EEPROM' (confidence: 8)

Driver `w83627hf' (should be inserted):
Detects correctly:
* ISA bus address 0x0290 (Busdriver `i2c-isa')
Chip `Winbond W83627HF Super IO Sensors' (confidence: 9)

I will now generate the commands needed to load the I2C modules.
Sometimes, a chip is available both through the ISA bus and an I2C bus.
ISA bus access is faster, but you need to load an additional driver module
for it. If you have the choice, do you want to use the ISA bus or the
I2C/SMBus (ISA/smbus)? y

If you want to load the modules at startup, generate a config file
below and make sure lm_sensors gets started; e.g
$ rc-update add lm_sensors default.

To make the sensors modules behave correctly, add these lines to
/etc/modules.conf:

#----cut here----
# I2C module options
alias char-major-89 i2c-dev
#----end cut here----

WARNING! If you have some things built into your kernel, the list above
will contain too many modules. Skip the appropriate ones! You really should
try these commands right now to make sure everything is working properly.
Monitoring programs won't work until it's done.
To load everything that is needed, execute the commands above...

#----cut here----
# I2C adapter drivers
modprobe i2c-nforce2
modprobe i2c-isa
# I2C chip drivers
modprobe eeprom
modprobe w83627hf
# sleep 2 # optional
/usr/bin/sensors -s # recommended

Do you want to overwrite /etc/conf.d/lm_sensors? Enter s to specify other file name?
(yes/NO/s): y
Done.
bash-2.05b#
[/code:1:20d7250eb8]

Majd a /etc/conf.d/lm_sensors fontosabb reszei:
[code:1:20d7250eb8]
MODULE_0=i2c-nforce2
MODULE_1=i2c-isa
MODULE_2=eeprom
MODULE_3=w83627hf
[/code:1:20d7250eb8]

Kiadtam a sensors-t
eredmenye:

[code:1:20d7250eb8]
bash-2.05b# sensors
eeprom-i2c-2-52
Adapter: SMBus nForce2 adapter at 5000
Memory type: DDR SDRAM DIMM
Memory size (MB): 256

eeprom-i2c-2-50
Adapter: SMBus nForce2 adapter at 5000
Memory type: DDR SDRAM DIMM
Memory size (MB): 256

w83627hf-isa-0290
Adapter: ISA adapter
VCore 1: +0.00 V (min = +0.00 V, max = +0.00 V)
VCore 2: +0.00 V (min = +0.00 V, max = +0.00 V)
+3.3V: +0.00 V (min = +0.00 V, max = +0.00 V)
+5V: +0.00 V (min = +0.00 V, max = +0.00 V)
+12V: +0.00 V (min = +0.00 V, max = +0.00 V)
-12V: -14.91 V (min = -14.91 V, max = -14.91 V)
-5V: -7.71 V (min = -7.71 V, max = -7.71 V)
V5SB: +0.00 V (min = +0.00 V, max = +0.00 V)
VBat: +0.00 V (min = +0.00 V, max = +0.00 V)
fan1: -1 RPM (min = -1 RPM, div = 1)
fan2: -1 RPM (min = -1 RPM, div = 1)
fan3: -1 RPM (min = -1 RPM, div = 1)
temp1: +0°C (high = +0°C, hyst = +0°C) sensor = thermistor
temp2: +0.0°C (high = +0°C, hyst = +0°C) sensor = thermistor
temp3: +0.0°C (high = +0°C, hyst = +0°C) sensor = thermistor
ERROR: Can't get VID data!
alarms:
beep_enable:
Sound alarm disabled

pic16c54 -i2c-0-4b
Adapter: bt878 #0 [sw]

Philips PAL_BG -i2c-0-60
Adapter: bt878 #0 [sw]

bash-2.05b#
[/code:1:20d7250eb8]
Az lsmodom:
[code:1:20d7250eb8]
bash-2.05b# lsmod
Module Size Used by
eeprom 6816 0
w83627hf 28584 0
i2c_sensor 3328 2 eeprom,w83627hf
i2c_dev 7936 0
i2c_nforce2 5248 0
sg 29728 0
floppy 54224 0
md5 3840 1
ipv6 237952 12
rtc 10424 0
snd_intel8x0 29096 1
snd_ac97_codec 68816 1 snd_intel8x0
snd_pcm 84872 1 snd_intel8x0
snd_timer 21380 1 snd_pcm
snd_page_alloc 7688 2 snd_intel8x0,snd_pcm
snd_mpu401_uart 6272 1 snd_intel8x0
snd_rawmidi 20260 1 snd_mpu401_uart
snd_seq_device 6536 1 snd_rawmidi
snd 47716 9 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 7648 1 snd
forcedeth 14848 0
i2c_isa 1920 0
ov511 77984 0
tvaudio 20768 0
tuner 18852 0
bttv 145356 0
video_buf 17156 1 bttv
firmware_class 7808 1 bttv
i2c_algo_bit 8584 1 bttv
v4l2_common 5120 1 bttv
btcx_risc 3976 1 bttv
i2c_core 19216 10 eeprom,w83627hf,i2c_sensor,i2c_dev,i2c_nforce2,i2c_isa,tvaudio,tuner,bttv,i2c_algo_bit
videodev 7552 2 ov511,bttv
sd_mod 13584 0
ehci_hcd 28292 0
usb_storage 64832 0
usbcore 102116 5 ov511,ehci_hcd,usb_storage
nvidia 4813268 12
3c59x 34984 0
ide_cd 37024 0
sr_mod 13860 0
scsi_mod 70080 4 sg,sd_mod,usb_storage,sr_mod
cdrom 36252 2 ide_cd,sr_mod
bash-2.05b#
[/code:1:20d7250eb8]
Mit rontottam el?