Linksys NSLU2

Jelenleg így fest a configom: Letöltés után lefut egy script a végén ami kitömöríti majd átmásolja az NMT-re a filmet /Nem szeretem a hálózatos lejátszást/

Ez a megoldás alapján: http://hup.hu/node/63900


hyperion@NSLU2:~$ cat .rtorrent.rc
# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.


# Maximum and minimum number of peers to connect to per torrent.
min_peers = 1
max_peers = 5

# Same as above but for seeding completed torrents (-1 = same as downloading)
min_peers_seed = 1
max_peers_seed = 10

# Maximum number of simultanious uploads per torrent.
max_uploads = 5

# Global upload and download rate in KiB. "0" for unlimited.
download_rate = 0
upload_rate = 90

# Default directory to save the downloaded torrents.
directory = /home/hyperion/torrent/download

# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
#session = /home/hyperion/torrent/.session

# Watch a directory for new torrents, and stop those that have been
# deleted.
schedule = watch_directory,5,5,load_start=/home/hyperion/torrent/watch/*.torrent
schedule = untied_directory,5,5,stop_untied=
schedule = throttle_3,18:30:00,24:00:00,upload_rate=90
schedule = throttle_3,00:01:00,24:00:00,upload_rate=0

# Close torrents when diskspace is low.
#schedule = low_diskspace,5,60,close_low_diskspace=100M

# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,"stop_on_ratio=200,200M,2000"

# The ip address reported to the tracker.
#ip = 127.0.0.1
#ip = rakshasa.no

# The ip address the listening socket and outgoing connections is
# bound to.
#bind = 127.0.0.1
#bind = rakshasa.no

# Port range to use for listening.
port_range = 6000-6001

# Start opening ports at a random position within the port range.
port_random = no

# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
check_hash = no

# Set whetever the client should try to connect to UDP trackers.
use_udp_trackers = yes

# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa

# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
# encryption = allow_incoming,enable_retry,prefer_plaintext

# Enable DHT support for trackerless torrents or when all trackers are down.
# May be set to "disable" (completely disable DHT), "off" (do not start DHT),
# "auto" (start and stop DHT as needed), or "on" (start DHT immediately).
# The default is "off". For DHT to work, a session directory must be defined.
#
#dht = off

# UDP port to use for DHT.
#
# dht_port = 6001

# Enable peer exchange (for torrents not marked private)
#
# peer_exchange = yes

#
# Do not modify the following parameters unless you know what you're doing.
#

# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
hash_read_ahead = 5

# Interval between attempts to check the hash, in milliseconds.
hash_interval = 10

# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
hash_max_tries = 3

max_open_files = 64

on_erase = rm_files,"execute=rm,-rf,--,$d.get_base_path="
on_finished = linkup,"execute=/home/hyperion/finish.sh,$d.get_base_path="